Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

User

MaddMan

Joined on the:

Dec. 19, 2018

Score

310

Comment(s)

3

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

1

Votes down received

0

Recent Activity

Question(s) asked

5

Answered question(s)

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question
RECENT ACTIVITY QUESTION(S) ASKED ANSWERED QUESTION(S) COMMENTED QUESTION(S)

02/01/2022

 Audi MaddMan (310Pts.)

0

dcryptor reset - Evo-All

Can you please dcryptor reset my evo-all Service# 001A06 831101. Hardware Vr:6 Firmware Vr: 4.18 Date 05/2018 It had been remote starting in my 2014 Audi Q5 with T-harness, the past few years. I recently purchased RM411 one way remote to extend range farther than factory remote. During programming on step 5 the yellow led will not light up or the antenna blue led flashing. Not sure if RF kit setting to H2 is ok, of if this matters. Tried both H1 and H2 in setting, no difference when trying to program. Firmware: 60.10 So, I master reset the evo-all to start over with settings and dcryptor. Received error message “dcryptor limit has been reached for this car”? Any suggestions for programming RM411, after getting remote start working with factory remote?
Login to reply View 1 answer(s)

26/12/2021

 Audi MaddMan (310Pts.)

0

Connecting RF KIT RM411 to EVO-ALL

2014 Audi Q5 push button start with EVO-ALL. Remot start works with factory remote for few years. Decided to upgrade remote to RM411. During progamming on step 5 the yellow led will not light up or the antenna blue led flashing. Not sure if RF kit setting to H2 is ok, of if this matters. Tried both H1 and H2 in setting, no difference when trying to program. Firmware: 60.10
Login to reply View 1 answer(s)

03/04/2019

 Audi MaddMan (310Pts.)

0

2014 Audi Q5 evo-all T-harness invalid key data (dcryptor step)

2014 Audi Q5 w/ keyport. Evo-all with t-harness sofware 60.02 loaded suggested options C1, D2, D6. Using installion guide 77161, following steps. Leds lightup as stated in steps 1-8. During dcryptor step, states "invalid key data". I reset module and tried again with same message "invalid key data" during dcryptor step. Looking for suggestions to get dcryptor step accomplished.
Login to reply View 1 answer(s)

28/01/2019

 Audi MaddMan (310Pts.)

0

Adding Linkr LT-2 RF antenna to EVO-All

EVO-ALL (T-harness) with Linkr LT-2 RF antenna

2009 AUDI A4 with key-port, auto transmission

Step 8 . LEARN THE TELEMATIC DEVICE TO THE EVO-ALL

In order to communicate with the remote starter, the Telematic device must be learned to the EVO-ALL.

1- Disconnect the 4 pin power connector from the Evo-All.

2- Press and Hold the Programming button on the Evo-All while plugging back the Black 4 pin connector.

3- The LED’s on the Evo-All will begin to cycle. Keep pressing the programming button until the RED &

BLUE LED’s are On.

4- Release the programming button.

5- Press & Hold the programming button again for 5 seconds until the BLUE & RED LED’s comes back On.

6- Release the programming button and Cycle the ignition to the ON position.

7- The RED, YELLOW & BLUE LED’s will be ON.

8- At that same moment the RED & BLUE LED’s will blink once to confirm that the MyCar ID has been

learned to the Evo-All.

9- Cycle the vehicle’s ignition to the OFF position to Exit EVO-ALL programming


I can not get red, yellow, blue leds on after cycle ignition on. Only Red and Blue leds are on.

Selected C1, D1, H2 settings for evo-all. Not sure if I need to connect another wire from harness

So the app will not lock,unlock,start,stop.

The Linkr LT app is downloaded on phone, account created, added car. The RF antenna red, green leds are solid/connected to network.

The app antenna icon is green, voltage battery icon is green and shows voltage. Select GPS icon and shows current vehicle location.

Login to reply View 1 answer(s)

22/12/2018

 Volkswagen MaddMan (310Pts.)

1

EVO-ALL PROGRAMMING 2006 VW JETTA

During programming at step #7 only the red LED flashes 6 times in a row/stops/starts again, not blue/red/yellow alternating as stated. I'm using TB-VW. Using guide #63221 for wiring/programming. All connections are solder and doubled checked wiring for errors. Using firmware 75.[35], hardware 6.0. CanBus Orange wires measure 2.5 volts. Yellow ignition wire has 12 volts minimum.
Login to reply View 1 answer(s)

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue