Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Bryan Phan

Joined on the:

Nov. 30, 2019

Score

240

Comment(s)

2

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

0

Votes down received

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

0

HON7 Connector D Pinout Incorrect?

Vehicle: 2019 Civic Type R PTS Evo One with HON7 Harness I noticed the pinout on the HON7 connector D does not match the documentation The pinout on my harness is as follows: D1: YLW/GRN D2: Blank D3: YLW/BLU D4: WHT/GRN D5: YLW/RED D6: WHT/RED Is this correct? I can only get the vehicle to attempt to crank but does not successfully start. I tried repinning connector D to match the HON7 documentation, this results in the car not starting at all during normal operation.

0

2019 Civic PTS Security Bypass Not Working and Incorrect clutch bypass

Issue 1: The remote starting fails to successfully start the vehicle. 

During cranking the dash security indicator continously flashes, this indicator is normally only flashing when the vehicle has been locked.  The dash security indicator begins to flash after the vehicle is shut down by the remote starter (from Ready Mode) and continues to flash until the vehicle is unlocked with the remote.

Parking light flashes four times after each failed cranking attempt.

Ready mode is operating as indicated, pressing brake while engaging the parking brake, then lifting off.  One parking light flash is indicated, the Red and Ylw leds on the EVO are on, and the motor continues to run until the driver door is open then closed.  Once the vehicle is shut down the dash security indicator begins flashing.

Blue Led flashes with each Lock Key signal from the OEM fob.  After three lock signals the Red and Ylw LEDs on the evo turn on and the start sequence begins.  The dash indicators come on and the dash security indicator led remains flashing. The starter is being actuated and the engine is cranking but the car does not successfully start.

Issue 2: Opening Red Wire on 4P clutch conenctor causing VSA and parking brake errors

In addition to the HON7 t-harness, Cut3, tap on Ylw line of Clutch Position sensor, and open of Red line on Clutch Stroke sensor (type R only) has been performed.

Without the opening of the Red line on the Clutch Stroke sensor the car will not activate the starter motor during remote starting unless I manually press the clutch pedal.  Once the Red line is opened as instructed, the remote start does actuate the starter motor, but now during normal operation there are now CONSTANT VSA and PARKING BRAKE ERRORS indicators on the dash. The vehicle does run and drive but with errors.

I posted this link in my earlier question, but it appears that opening the Red line causes the VSA system to malfunction and putting a relay on the Ylw line of the Clutch Stroke sensor maybe an alternate method? I am not sure how to do this with the EVO configuration.

https://github.com/JW0914/Wikis/blob/master/Automotive/FK8%20CTR/Compustar/Alarm%20%26%20Remote%20Start%20Install.pdf

Please advise on updates or alternate configuration. My setup specifics are listed below:

Vehicle: 2019 Civic Type R PTS Manual

Bypass HW: 4 FW :3.32

Remote Starter HW:7 FW 1.24

T-harness: HON7

All reccomended options were loaded for both Bypass and Remote Start, only the Ready Mode Option was modified from 33.1 to 33.2.

The decryptor programming was performed twice with nominal LED and Flah Link Updater feedback

0

2019 Civic Type R Red Wire Clutch Switch Location

The EVO wiring instructions specify that the 2019 Civic Type R (Push-to start) has an addtional red wire on a four pin Clutch Switch; this wire need to be cut. I could not locate this Clutch Switch connector with a red wire in a 2019 Civic Type R (USDM) and could not find any pictures or other references to this connector location in the instructions. The only connector near the clutch assembly is the a four postion 2 wire connector that matches the docutmentation, this connector has only the yellow and black lines. Where can I find this additional red clutch wire? Thanks, Bryan

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue