Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Ahmed Aboushouk

Joined on the:

Aug. 10, 2021

Score

330

Comment(s)

12

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

0

Votes down received

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

0

Renault Kadjar 2020 Evo All standalone

I have a Renault Kadjar 2020 with push button, I want to install Evo All as a standalone solution for remote starting the car, Renault Kadjar and Nissan Rogue Sport share their major components and are similar in a lot of aspects, they have the same BCM and same wiring sockets, I have followed the guide for Nissan Rogue sport and there are differences in the following : 1- OBD ignition ( pin 8 is empty ) 2- 24 Pin Black Socket ( Pin 19 is empty while Blue wire is on Pin 20 ) 3- 40 Pin black Socket ( Pin 9 is empty ) 4- Most of the Wiring Colors are different than the guide Please keep in mind that i have already used the same solution on a Nissan Qashqai ( similar to rogue sport ) but with a T harness and it worked My main concern now is to have a correct wiring guide for Renault Kadjar and i am confident that it will work

0

Fuse rating for EVO-ALL power supply

I am about to install EVO-ALL for Standalone installation ( without the T-Harness ) for a nissan Qashqai ( Rogue sport in CA ) with push to start ( Guide # 83931 )

S/N of my EVO-All is : 001A07026604

I have three main questions so i can complete the installation :

1- Fuse rating for the power supply of the module ( between B4 pin and 12v battery )

2- Diodes direction is confusing me as the Ignition A4 pin is an output pin which means that Current should flow from EVOALL to the car BCM pins while the Diodes direction says the opposite  ( cathode at top meaning current flows from BCM pins to EVOALL )

3- Which is more recommended for a way of control to disable remote starting when needed ( i cannot have Alarm functions beside remote starting for this vehcile ) where 2nd option would completey shut off the power to EVOALL :

- Adding ON/OFF switch on the Hood Pin A8( connecting other switch end to ground )

- Adding ON/OFF switch on B4 pin on the same line of the Fuse ( connecting other switch end to ground )

  Many thanks in advance for your support & cooperation

0

Alarm activation when locking with OEM Fob

I have an EVO ONE with alarm system activated ( with connected to the Horn ), I donot have any OEM alarm from the manufacturer, My car is nissan qashqai with push button. Alarm used to be activated when i locked the car using OEM fob or door button ( If i recall correctly ), Now it is only working when locking with RF kit remote ( crimestopper ) while it doesnot trigger the alarm when locking with OEM fob . Is there any programmable option that i did my mistake or i am missing to restore the orignial feature. I want the alarm to be activated whenever the vehicle is locked from any source ( door button or OEM fob or RF kit remote ) thanks in advance It is S/N : 001A07026604 and i am using a T harness

0

VALET mode from crimestopper REVO4.1 remote :: Turbo mode activation

I have an EVO-ONE for remote start and built in Alarm ( using the horn ) EVO-ONE S/N : 002B04198955 The setup is configured for a Nissan Qashqai ( rogue sport ) 2019 with a PTS ( using T harness ) I have installed the crimestopper REVO4.1 rf kit succesfully and i have two questions : 1- How to enter the Valet mode from the REVO remote ( their guide is very basic and did not mention how to do so , Though i discovered by luck that holding the trunk button would disarm the EVO only for temp time till i lock again but do not know how to trigger the Valet to stop the starter and alarm completely ) 2- I cannot find a way to activate turbo mode ( it is already enabled in option 19 with 2 minutes runtime ), while the engine is running and i am inside the vehicle, i press the remote start on Revo remote ,The Car acknowledge by 3 parking light flashes then if i press the ignition push button the car shutsdown ( while it should keep running and then i should leave the car and lock it to activate turbo for the 2 minutes ) I am stuck on the part that it shouldnot shutdown when i press the push button I tested also with the same procedure but without pressing the push button , the car keeps running for more than 5 minutes ( i believe it should be in idle mode and will shutdown after the full 15 minutes but i didnot test to wait for 15 minutes ) Sorry for the long description and thanks for your support

0

How to activate Evo All Alarm on a 2019 nissan qashai

I have successfully installed Evo All as a standlone setup with a T harness on 2019 nissan qashai with push to start I donot have a factory alarm installed I only have factory horn 1x chirp after lock from oem remote and no chirps for the unlock I searched and found that pin A4 in the evo ( green ) should go to the horn signal and to enable options G in the evo I see from my car guide that pin A4 is already in use for the Ignition so i cannot figure it out how the evo can control the horn I have enabled options G and nothing happened ( expected ) Please advise how can i add the evo alarm features to my current setup My evo s/n : 001A07026604

0

Nissan Qashqai 2019 Steering Lock Plug wiring

I have successfully installed standalone evo one for nissan qashqai 2019 with push to start When i remote start the vehicle and then enters inside it then when i press the Ignition so i can start diving, car refuses to accept ignition saying steering is locked and doesnot allow car to be on the ON position I have tried enabling door shutdown option and it actually shutdown car when any door is opened So in the current setup , i have to press brake after entering then it shutdowns then i start it normally again I saw something about steering lock plug connector but i donot know which wires in the A plug harrness to connect to ? I have a white/green wire but there is no white/red Please assist me as i want to start driving directly after entering the vehicle

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue