Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

05/08/2022

 Toyota Cuong Nguyen (130Pts.)

0

Do factory remote fob and RM442 fob work to start/ stop remote start? Trunk?

I have a dot key for a Toyota sequoia 2010. Can I use the stock fob to turn off the remote start? If I get the extended range add on, would the tailgate function work with the new remotes? Would I be able to still use the stock remote with thr add on remotes?
Login to reply View 1 answer(s)

20/12/2021

 Toyota Daniel g (160Pts.)

0

2014 Camry fob not working after remote started?

When 3X lock is pressed vehicle starts. Then when started the FOB doesn't work while vehicle is running and have to use the key to enter the vehicle.

I've installed 2 other remote starts in 2013 Corolla and 2016 Tacoma, and after vehicles has started, I can still use the key FOB to unlock the door. I can also click 3X on the lock and shutoff vehicles. But I can't do it with 2014 camry...did I miss a wire? or is this normal operation?

thank you.

Login to reply View 1 answer(s)

25/04/2021

 Toyota Stefan David (310Pts.)

0

EVO-ALL thar-toy13 harness connections all in do i need to leave any disconnected?

wont start and no led indications whatsoever on module when key fob button pushed 3times .

Any experienced with EVO-ALL thar-toy13 harness connections ,all plugs in do i need to leave any disconnected?

Login to reply View 2 answer(s)

25/04/2021

 Toyota Stefan David (310Pts.)

0

EVO-ALL thar-toy13 harness connections all in do i need to leave any disconnected?

wont start and no led indications whatsoever on module when key fob button pushed 3times .

Any experienced with EVO-ALL thar-toy13 harness connections ,all plugs in do i need to leave any disconnected?

Login to reply View 2 answer(s)

20/12/2020

 Toyota Natalie Maldonado (880Pts.)

0

2009 Toyota Tacoma Evo One Programming successful, but wont start

After successful programming, we couldn't figure what exactly is wrong. Continuity was checked on every single wire configuration and all tested properly wired. Hood pin, lock/unlock/lock Unit S/N 002B04 107018 Is there anything else needed that we are missing? Thanks in advance
Login to reply View 1 answer(s)

29/08/2020

 Toyota ARUN Chandran (240Pts.)

0

2013 Toyota Venza takeover?

I have Evo All hardware version 6 latest firmware, when I open the door the vehicle shuts off, is takeover available?
Login to reply View 1 answer(s)

14/08/2020

 Toyota ARUN Chandran (240Pts.)

0

2013 Venza remote start not working

I hardwired all the connections and they are good. The three lock presses dont do anything. If i ground out the yellow wire i hear some relays clicking but nothing happens. The vehicle is push to start. The module is EVO-RS One thing i noticed is in the instructions it states after the blue LED is blinking rapidly when I press the start button again the blue led should turn off but it continues to blink slowly.
Login to reply View 2 answer(s)

14/08/2020

 Toyota ARUN Chandran (240Pts.)

0

2013 Venza remote start not working

I hardwired all the connections and they are good. The three lock presses dont do anything. If i ground out the yellow wire i hear some relays clicking but nothing happens. The vehicle is push to start. The module is EVO-RS One thing i noticed is in the instructions it states after the blue LED is blinking rapidly when I press the start button again the blue led should turn off but it continues to blink slowly.
Login to reply View 2 answer(s)

14/08/2020

 Toyota ARUN Chandran (240Pts.)

0

2013 Venza remote start not working

I hardwired all the connections and they are good. The three lock presses dont do anything. If i ground out the yellow wire i hear some relays clicking but nothing happens. The vehicle is push to start. The module is EVO-RS One thing i noticed is in the instructions it states after the blue LED is blinking rapidly when I press the start button again the blue led should turn off but it continues to blink slowly.
Login to reply View 2 answer(s)

16/01/2020

 Toyota Jay Williams (150Pts.)

0

EVO-ALL - OEM Fob not working to unlock after remote started. TPMS is cut and works.

I flashed EVO-ONE to latest firmware, used the wizard to set my settings, then went into pro mode and followed the steps in documentation to select XL202 RF kit, and installed in the vehicle. The SmartStart module is not yet installed. 3x lock works with OEM fob but once started, the OEM fobs no longer work to lock/unlock the doors. I did cut the TPMS wire and does not flash when started with key or after key is in ignition and turned to ON. I did test alternating the D6 and D4 wires on the cut TPMS wire but still had no unlock from fob after remote start. My suspicion is that since the TPMS light doesn't flash in standard operation, enabling the RF kit might have something to do with this but since I didn't test the install before I enabled that, I'm not sure. Is there something else I might be missing?
Login to reply View 1 answer(s)

10/01/2020

 Toyota Sergei Yakhnes (160Pts.)

0

will the evo one 3x lock factory fob function work on toyota venza 2013 g key ?

3x lock oem fob start toyota venza 2013 with gkey
Login to reply View 1 answer(s)

13/09/2019

 Toyota Colin McCreary (240Pts.)

0

Toyota Tacoma Evo one installed but will not start or blink after being programmed.

I installed the Evo one using the instructions. When I was done programming and I removed the key from the ignition. The red light disappears and then no lights will reappear again. I have tried to re program and have checked every wire 5 times. The truck does not attempt to start when the button sequence completed, it acts normal. I am unsure what to do at this point.
Login to reply View 1 answer(s)

05/04/2019

 Toyota emanuel orduna (160Pts.)

0

Will factory remote, remote start a 2012 toyota venza with G key

Im looking to buy a remote starter with tharness, what will i need to conplete instalation?
Login to reply View 1 answer(s)

21/01/2019

 Toyota Jackie Burks (130Pts.)

0

Remote start not working.

Have the Evo One, and after install with the TOY harnesses, remote start not working. After checking all firmware was updated and installed the unit, when I pressed the OEM remote 3x every lit up but did not start. All it did was unlock my doors.
Login to reply View 1 answer(s)

12/12/2017

 Toyota Dan Hughes (160Pts.)

0

Evo One only responds to OEM key fob when ignition is on (2018 4Runner)

2018 4Runner with T harness. Installed with all wires soldered/taped. Double checked all wiring for correct location and proper connection. Everything on the installation side is good. Problem... I cannot use the 3x lock function as the Evo-One will not blink (blue led or anything else) with the key off. I can turn the ignition on and it blinks and responds to OEM fob lock/unlock. I can start the vehicle and press the lock button on the fob 3x and then turn the ignition off / remove key and the vehicle will stay running. I can also press the lock button 3x again and the truck will shut off with the fob..But then it will not respond anymore.. So the programming is correct, the wiring is correct, but for some reason on this 2018 4runner (standard key/t harness install), the door lock/unlock doesn't read when the ignition is off. My 2016 4Runner worked as it should, reading the lock/unlock regardless of ignition switch position, so not sure if its something in the newer vehicle (installation guide shows to be for up to 2018), or if there is something wrong internally with the new evo-one (purchased 2 weeks ago, installed Saturday 12-10-17)
Login to reply View 2 answer(s)

25/10/2018

 Toyota TundraJD (180Pts.)

0

2015 Toyota Tundra Evo One remote start alarm goes off on remote shutdown

**This may be a duplicate post but has more info and i will try to hide the other post installed evo one in my 2015 tundra with OEM alarm. The truck does remote start fine (after the doors unlock and relock) but if it runs for 15 minutes, the alarm goes off. If I remote shutdown right after remote start, it works as it should. If i remote start and wait 5 minutes and remote shut down the alarm goes off. I have hooked up the keysense wire to the black wire as instructed in the diagram. Alarm is triggered when using RF 642 remote or OEM 3x lock. I did use a pre-wired kit that had both plug and play adapters for the Tundra. Updated to 74.49 via flash link but no change.
Login to reply View 2 answer(s)

25/10/2018

 Toyota TundraJD (180Pts.)

0

2015 Toyota Tundra Evo One remote start alarm goes off on remote shutdown

**This may be a duplicate post but has more info and i will try to hide the other post installed evo one in my 2015 tundra with OEM alarm. The truck does remote start fine (after the doors unlock and relock) but if it runs for 15 minutes, the alarm goes off. If I remote shutdown right after remote start, it works as it should. If i remote start and wait 5 minutes and remote shut down the alarm goes off. I have hooked up the keysense wire to the black wire as instructed in the diagram. Alarm is triggered when using RF 642 remote or OEM 3x lock. I did use a pre-wired kit that had both plug and play adapters for the Tundra. Updated to 74.49 via flash link but no change.
Login to reply View 2 answer(s)

25/10/2018

 Toyota TundraJD (180Pts.)

0

2015 Toyota Tundra Evo One remote start alarm goes off on remote shutdown

**This may be a duplicate post but has more info and i will try to hide the other post installed evo one in my 2015 tundra with OEM alarm. The truck does remote start fine (after the doors unlock and relock) but if it runs for 15 minutes, the alarm goes off. If I remote shutdown right after remote start, it works as it should. If i remote start and wait 5 minutes and remote shut down the alarm goes off. I have hooked up the keysense wire to the black wire as instructed in the diagram. Alarm is triggered when using RF 642 remote or OEM 3x lock. I did use a pre-wired kit that had both plug and play adapters for the Tundra. Updated to 74.49 via flash link but no change.
Login to reply View 2 answer(s)

18/10/2018

 Toyota Joe Callaco (380Pts.)

0

MyCar app not showing runtime and only starts less than half time.

2014 RAV4. EVO All. Crimestopper Cool Start RS00-G5. T-harness. I finally got this setup to work with the OEM black H-key remote with 3X Lock press. I still don’t get a parking light conformation, and the doors won’t unlock, via automatically or with the fob. The MyCar app shows battery and signal levels, and GPS location. No runtime, or remote start conformation. It only seems to start after I open the map and it is located. Then it will start, shutdown and locks require the same. I do have a Fortin flashing tool, and don’t know what else to do. Please help?!?! Thank you!
Login to reply View 1 answer(s)

26/06/2018

 Toyota Juan L Amezcua (250Pts.)

0

Installed but nothing happened no alarm and remote start works

I did the install as recommend for 2008 Toyota Corolla don't key, ( connection 1 , program 1) manage to program the evo one I used the OEM controls and nothing happened, no alarm working remote start not working either
Login to reply View 1 answer(s)

18/03/2018

 Toyota William Quigley (180Pts.)

0

remote start will only work when key is next to barrel ?

toyota 2010 rav 4 evo one with out t harness basically the evo one is not emulating the transponder please help is ther anything i can do to fix this or do i need to buy a evo key module to emulate the immoblizer everything work just fine but remote start will not start the car it will just crank ....unless i put the key nest to the barrel then it will start
Login to reply View 1 answer(s)

26/02/2018

 Toyota David Doss (130Pts.)

0

2015 Toyota Tundra alarm triggered on start and won't unlock with keyfob during remote start session.

truck starts with factory keyfob lock press 3x. after it is running, it will not unlock with the keyfob. also, if given time for the alarm to activate, triggering a remote start with factory keyfob lock x3 sets off the alarm. i received unit pre-programmed from a seller. thanks in advance for your help!
Login to reply View 1 answer(s)

25/01/2018

 Toyota Trevor W (240Pts.)

0

3x times OEM remote start not working - FJ Cruiser

2008 Toyota FJ Cruiser

I have the Evo-One with TOY1 T-Harness and Flash Link Updater.  I am unable to get remote start to work.  I have triple checked all of the connections.  The unit does program correctly.  I have enabled option 38.2 for pressing 3x Lock to remote start.  I have turned ON option C1 for OEM remote monitoring.  And I get no response from anything when pressing the Lock 3 times on the remote.  Yellow loop has been cut.

Suggestions?!

 

EVO-ONE  (Connection Mode:Bypass) Service No: 002B02 213919 Preload date: 43-2017 Hardware version: 2 Firmware version: 79.43 Vehicle: TOYOTA FJ CRUISER 2008 - STANDARD-KEY   EVO-ONE  (Connection Mode:Remote Starter) Service No: 002B07 213919 Preload date: 43-2017 Hardware version: 7 Firmware version: 1.24   FLASH-LINK UPDATER Service No: 002504 052723 Preload date: 50-2017 Hardware version: 4 Firmware version: 4.03
Login to reply View 1 answer(s)

30/12/2017

 Toyota Mike Payne (490Pts.)

0

2012 Toyota Highlander G key EVO-ONE OEM remote active while running?

Customer called wanted price on vehicle. Is remote active during 3x lock remote start? I know for 100% 2012 - 2014 Camry IS NOT. Found that out the hard way. Anyone know for a fact it is? I don’t see anything about TPMS wire cut in this vehicle like newer Toyota’s??? I know toyota is one of the weird ones that some do, some will not and some you have to do the TPMS trick. Please advise. Thanks in advance.
Login to reply View 1 answer(s)

30/12/2017

 Toyota Amanda Lloyd (130Pts.)

0

OEM key fob not working while 2017 Rav4 is remote started

I hooked up my Evo-One for remote start only (using my OEM key fob, 3x lock button) on my 2017 Toyota Rav4 H-hey and it starts up fine but it will not allow me to unlock my vehicle once it is remote started. All of my wires are hooked up correctly, per guide #58371 & I have the C1 & D2 turned on as well as the A2 off under bypass programming and 38.2 selected under the auto-start programming. I assume it is a programming issue, something is either on that isn't supposed to be or I have something off that isn't supposed to be. The TPMS wire is also cut and not touching and the Lt.Blue "data door lock" wire is hooked up correctly. Help please.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue