Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

31/10/2024

Toyota G M (14810Pts.)

0

2022 Hilux

Hello. Is there a manual for installing evo-one on 2022 Hilux? Key.

0

Evo-one with Oem remote

Hi Sir Please help 2022 Toyota Sedan push Start Evo one is connected by THAR-TOY13 for Toyota programmed in car & did key transfer Dcryptor. Evo one has been update. everything was done right, but the cardoes not start remotely.when press the lock 3 times no led light on and yellow loop has been cut. Evo-one SN: 002B04 248953 Thank you very much

22/05/2024

Toyota G M (14810Pts.)

1

2014 4runner (key)

Hello. With evo-one, can I start a 2014 4Runner with an OEM key fob? 3x lock

11/04/2024

Toyota G M (14810Pts.)

0

2010 camry CAN wires

Hello. For a 2010 Camry (hybrid), where else can find CAN wires other than OBD?

21/03/2024

Toyota G M (14810Pts.)

1

2010 camry

Hello. I installed evo-all (3x lock...001A07582654) on a 2010 camry hybrid. After starting from the standard remote control, the remote control no longer responds unless we touch it on the car window. I installed the second module, but again the same.

03/02/2024

Toyota G M (14810Pts.)

2

Avalon of miracle.

3 days ago one module did not work on 2013 Avalon. Today the 2015 Avalon arrived and neither that module nor the other module worked for this one either... Then CAN transferred the wires to a 30-wire connector and both modules started working (???). Maybe they have a standard autostart and it interferes or what?

0

2022 Toyota 4runner - pushbutton start, wired with tharness, wont start with 3x lock?

Using guide# 107711. Evo-all with Toy6 tharness. Everything wired per the guide, used the tharness plug "B" at the bcm, spliced 12v+ and ground at the obd port, and cut the pink telematics wire on the back of the bcm, and connected the cut ends to the two wires on the red 6 pin connector per the instructions. Everything the guide say to do is done. The lights lit up per the programming procedure and went out at the end. Got out and shut the door to try 3x lock and the parking lights and locks cycle like they should, but the dash lights dont come on and no remote start? Ive installed a few fortin evos in the past, and theyve always worked fine from here, just not sure what Im missing. the 4runner starts up like normal when I get in and push the brake, but its like the fortin isnt even there. Just not sure what to try next.

23/12/2023

Toyota G M (14810Pts.)

0

2020 camry

Hello. I installed evo-one on a 2020 Camry (002B04337440). Everything works, the parking lights don't come on. What to do?

23/12/2023

Toyota G M (14810Pts.)

0

2020 camry

Hello. I installed evo-one on a 2020 Camry (002B04337440). Everything works, the parking lights don't come on. What to do?

30/11/2023

Toyota G M (14810Pts.)

1

2022 PRADO

For the 2022 Prado I indicated the 2018 LC150(euro). I connected CAN in the middle BCM connector. Blue is high, white is low. + and - I connected to the OBD. The parking lights turned on themselves...Even the position of the auto light lever did not interfere. The steering wheel did not close at all and did not have SLP either.

29/11/2023

Toyota G M (14810Pts.)

0

2022 fortuner

Hello. Which instructions are suitable for Fortuner 2022? PTS.

0

2020 Camry Hybrid engine not starting via remote start

 

 

Hello everyone, I have a 2020 Grande Camry Hybrid, and I bought a long range remote start device with one all evo and THAR-TOY13, and I connected plug to plug without cutting any cable with a flashing, but the remote start did not work

Please see the attached picture, there are signs I have put for inquiries

http://photos.app.goo.gl/Lv4woU1btxjDtxf28

0

3-locks-to-start stopped working after module flashing / added RF kit

Hi,

My evo-all used to working with the OEM key 3-locks-to-start before.

Then I bought the RM 942 RF KIT.

Flashed the evo-all to 78.70, and the antenna to 1.05 already.

I flashed my evo-all to match my vehicle: * Toyota Sienna 2020 * Standalone installation * Standard connection * push to start * No alarm     Enabled the H&H2 option and paired the RF kit keys successfully, with the hlpe from https://www.fortin.ca/en/qa/121700/rm-942-buttons-have-wrong-functions

Followed the DCRYPTOR PROGRAMMING PROCEDURE. All leds are off at step 5 indicating it's already programmed.

After all these, it seems everything are connected and paired correctly. The lock/unlock buttons on the RF kit work properly.

 

BUT neither OEM key 3 locks nor RF kit key remote start ([+] + lock) could remote start the car. After pressing the OEM key 3 locks, I can hear the evo-all or some car electric component making the small clicking sounds, and the car turn signal lisghts had a couple of follow-up flashing, which seems to me like the evo-all is indeed carrying out the remote start procudre. But car does nothing, no cranking sound at all.

 

Did I miss anything again?

 

One weird thing to me is that I think I installed my evo-all with a T-harness, but in the Flash Manager software, after I select TOYOTA, SIENNA 2020, PUSH-TO-START, STANDALONE, there is only STANDARD CONNECT option but on T-HARNESS CONNECTION option in the connection type selector. Is this the problem?

 

Thanks,

Gerry

 

11/06/2023