Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

18/12/2023

 Honda G M (15380Pts.)

1

2014 Honda civik

Hello. I installed evo-one on a 2014 Honda Civic. I indicated a hybrid - D4... The car switches to a hybrid only when braking. Should I keep this D4 or delete it? 002B04337437
Login to reply View 1 answer(s)

09/07/2023

 Honda G M (15380Pts.)

0

2014 honda accord

Hello. I installed evo-all(001A07473343)+remote start, on a 2014 accord(hybrid-pts). Remote start opens doors and then doesn't close.
Login to reply View 1 answer(s)

18/12/2022

 Honda Sean Meehan (130Pts.)

0

2104 Honda Accord Remote Start does not work after programming and Installation

I have all the wires in place, have a toggle kill switch, programmed correctly and did the Flashlink Dcryptor. When I attempt to remote start, it does not start. I see a blue led light the controller when I hit lock on my key fob, but that's it. I have a 2014 Honda Acord Push Start. With the remote start in place, the car still operates as normal.
Login to reply View 1 answer(s)

25/10/2021

 Honda Fred Khan (230Pts.)

0

2014 Honda Odyssey. Check keyless starting system message on dash

2014 Honda Odyssey  push to start.  Instillation with Evo one and Thar one Hon8 tharness. Programming and dcryptor went smooth. 3xlock to  start and take over are working.  Only issue is, I'm getting  check keyless starting system message on dash at all times.  I've read  in  the fourm that this light is normal under remote start as the key is not present but should go away once  the car is started normal.  However in my case the light is on always even when I start the car normally .Any help would be appreciated
Login to reply View 1 answer(s)

21/01/2021

 Honda jacob longstreet (130Pts.)

0

Worked for a couple days then car wouldn’t do anything

I have a 2014 Honda Accord push to start that I installed the evo one in with the t harness. Everything worked fine for a couple of days and then went to start the car and nothing would work. It was like the car was locked down and had no power. Couldn't unlock doors or open trunk or use the horn from the key fob. After calling a locksmith to break into the car I unplugged the eco one harness and hooked everything back up to how it used to be and the car works fine now. Is their a short somewhere in the evo one or why would it work fine for a couple days and then act up like this?
Login to reply View 1 answer(s)

22/11/2020

 Honda Willkai (160Pts.)

0

2014 Honda civic pts manual transmission ignition turn on after reservation Mode set

After set the reservation Mode, closed door while engine running then shut off which the reservation Mode set, then ignition will turn on right after shut down, triple check wiring , all okay please help
Login to reply View 1 answer(s)

07/03/2019

 Honda Rev_Nev (150Pts.)

0

2014 Honda Civic - Can I use Function 38 Mode 5 (38.5) Instead of Function 38 Mode 2 (38.2)?

I am going through the FlashLink Manager setup on my Evo One & THAR-ONE-HON3 and was curious if I can use 38.5 (Lock-Unlock-Lock to remote start) instead of using 38.2 (Lock x3 to remote start)? The vehicle specific manual says to use 38.2 but I would prefer to use 38.5. Is this possible?
Login to reply View 1 answer(s)

25/02/2019

 Honda Ron Shah (280Pts.)

0

2014 Accord PTS - Discrepancy in Instructions?

2014 Accord Push to Start

Evo-One w/ T-Har-One-Hon3

 

    Instructions on Fortin website indicate that D2 must be turned on during programming if equipped with OEM alarm. I did not turn on D2 and it is working fine, is there a reason D2 must be enabled?
      I left D2 off as it seems to be more secure because there if D2 is enabled, there is a period during which the vehicle is left unlocked, so if someone was walking by and heard the vehicle unlock, they could access the vehicle before it starts and relocks.
Login to reply View 1 answer(s)

23/01/2018

 Honda Mohammad Odeh (420Pts.)

0

Honda CR-V 2014 Evo one

i have honda crv 2014 standard key , and i am installing evo one with T-harnes 2 and RF2W antina fob , i connect same what is show , i and i follow the instruction solied red then push twich flash red , then pust the key to ignition fast red falshing but the blue light will not show after 10 flashing and even at all all the wires are connected by the T harnes and the orand wire and the pink wire are connected for each connecter 12 pin and the 20 ping , the ground is connected , the only wire is not connected is the fuesed wire which is pin 1 white or brown in the T harness which is said it is output , i never touch the programming yet for the interface of the unit which is still the default setting from the manfacure , any advice or suggestion . ?

 

is the E1 wire with the Fuse should be connected or not , the installation manual it is show 2 diffrent way , i am using the Rev 2 Thar hon 2

 

Service NO 002b07228755

Login to reply View 1 answer(s)

22/01/2018

 Honda Mohammad Odeh (420Pts.)

0

Honda CR-V 2014 Evo one

i have honda crv 2014 standard key , and i am installing evo one with T-harnes 2 and RF2W antina fob , i connect same what is show , i and i follow the instruction solied red then push twich flash red , then pust the key to ignition fast red falshing but the blue light will not show after 10 flashing and even at all all the wires are connected by the T harnes and the orand wire and the pink wire are connected for each connecter 12 pin and the 20 ping , the ground is connected , the only wire is not connected is the fuesed wire which is pin 1 white or brown in the T harness which is said it is output , i never touch the programming yet for the interface of the unit which is still the default setting from the manfacure , any advice or suggestion . ?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue