Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

11/12/2019

 Chevrolet Jim Stone (320Pts.)

0

Can I use the OEM remote or do I have to install an RF kit on a 2014 tahoe?

EVO ALL with THAR-GM4 stand alone harness. Flashed to current firmware and did the key Dcryptor. The LED lights flashed exactly as they are supposed to during the programming steps. OEM remote will not start vehicle after pressing lock button 3 times.
Login to reply View 1 answer(s)

17/12/2019

 Chevrolet joe tom (410Pts.)

0

2014 malibu t-harness installation parking light

hello, i am installing a evo-all on a 2014 malibu and the flashlink software shows A14 as the parking lamp. however the instructions i'm following 63361 state the parking lamp is wired differently with a module i am not using. can i safely use the a14 wire to the suggested gray parking light wire?
Login to reply View 1 answer(s)

07/04/2019

 Chevrolet James Mayer2 (130Pts.)

0

2014 Chevy Cruze dash lights up but no crank

I installed my EVO All (Service# 001A06 853981) in my 2014 Cruze. When I push the OEM lock button 3x, the dash lights up but the car does not crank. All doors, trunk, and hood are closed. Options C1, D1, and D2 are all ON.
Login to reply View 1 answer(s)

27/08/2018

 Chevrolet David Davis2 (310Pts.)

0

2014 CHEVY CRUZE FLIP KEY - SEVICE THEFT DETERENT SYSTEM Manual Transmission

I am still having issues with my Evo All and Crimestopper modules. I am able to get the car into reservation mode by putting the car in nuetral and setting the ebrake. Once the car is in reservation mode I can pull out the factory key and get out of the car and lock the doors and the car shuts off. Everything is good up until I try to remote start the vehicle. The driver information system starts doing its checks but then stops and says "Service Theft Deterrent System". I have already performed a master reset on the evo all module with no luck. All I am looking for here is a list of things to try. One thing that I am confused about is the disarming of the alarm since the Crimestopper can unlock the car before the remote start and so can the evo all. I have also read in some questions that the immo wire needs to be cut but I am using the GMT T-harness for connections to the car.
Login to reply View 1 answer(s)

13/01/2018

 Chevrolet Logan McElhatten (130Pts.)

0

2014 Cruze decrypted successful plugged back in does nothing for 3x lock start evo rs gm1

2014 Cruze lt standard key everything wired correctly did decryption and it said successful plugged back in will not start in 3x remote start mode. Gm1 evo rs package. Tried calling support center on hold 2 hrs without talking to a Damn person. Never blinked blue slowly when I tried the plug connector at the end of bypass programming just stayed solid but I did do decryption. Connected everything up right but does not work
Login to reply View 1 answer(s)

22/12/2017

 Chevrolet Gene Chiu (130Pts.)

0

Buying EVO-GM1 for 2014 Chevy Cruze

Hi there,

 

I would like to buy Fortin  EVO-GMT1 this remote starter system, but I have some question I wish that you help me.

 

Do I need to buy flash-link updater or I just need to buy Fortin  EVO-GMT1 then after installing I can use directly?

 

I'd use the 3X lock button on the OEM remote.

 

My car is 2014 Chevy Cruze LS.

 

Thank you.

 

Gene

Login to reply View 1 answer(s)

31/10/2017

 Chevrolet Jason Anderson2 (130Pts.)

0

No lights on the EVO-ALL, no remote start working on 2014 chevy cruze

Hello, I have a 2014 Chevy Cruze I'm trying to set up in stand-alone configuration with an EVO-ALL. Service number is 003606 007301. Flip-key, not push-to-start. I have the flash-link-4 module, which seems to be working fine. Unit appears to be doing nothing at all. Initially, when I plug it in, all 3 LEDs flash simultaneously a few times, then nothing happens. To be clear, after the initial plug-in, no lights appear on the EVO-ALL at all, even when a button is pressed on the remote (I believe I read that I should see the blue light flash indicating data is being passed, is that correct?). Does this mean my CAN-connector is not connected properly? I am plugging in the 4-pin connector first, as per the instructions, then the rest of the wires. I don't care whether it's lock-lock-lock or lock-unlock-lock (as I currently have it programmed). I've tried both ways. What am I doing wrong?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue