Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

18/01/2023

 Ford Todd Lusby (130Pts.)

0

2010 ford escape KEY-OVERRIDE-ALL

I'm installling the KEY-OVERRIDE-ALL with a DEI remote start. When I attempted to program prior, I would see the LED start flashing, but programming didn't complete. Now when I attempt to program, the LED on the module stays on and the security light on the dash flashes rapidly. I've confirmed I have 12V on Red, Ground on Black, Ignition on Yellow, and remote start staus on Blue. Is there anything else i should try on this module? The module was purchased new in December and hasn't been installed in another vehicle.
Login to reply View 1 answer(s)

16/01/2022

 Ford chris fata (130Pts.)

0

evo-all can not get into programing mode light stays red

evo light stays solid red when pluged in with button pushed in
Login to reply View 1 answer(s)

27/12/2021

 Ford ryk (220Pts.)

0

2011 Ford Escape red light stays on during programming - SOLVED

Vehicle: 2011 Ford Escape

Evo All #001A07260304 installed with T-harness THAR-FORD4; plug-n-play install, teed connections to ignition switch, immobilizer antenna and OBDII connector; no wires spliced

Can't get the unit to program.  Process: Hold program button, plug in data cable and release on red light.  Insert key and turn on until theft light turns out.  Remove first key and insert second.  Turn on for 3 seconds, theft light goes out, turn off and remove.  Last step says to press and release programming button within 5 seconds (this is where it gets stuck).  Red light should flash 10 times and blue light should flash 10 times and ignition comes on and turns off again.  When I press the button the last time, the red light blinks and just stays on.

I've tried the firmware downgrade listed in https://fortin.ca/en/qa/92073/faq-red-led-stuck-on .  That link says to downgrade to v 0.99 but the lowest version for Ford appears to be 4.01.  I flashed 4.01, power cycled in vehicle, reflashed v 71.52, unlocked settings and reset the unit.  Still same results.

I've also tried testing the data bus.  Hold button, insert data link connector, release button on blue light.  Connected all other connections and turned key on.  Blue light stays solid.  Shouldn't it flash on data?

The yellow wire is not connected as it seems to be part of the T harness, but I've tested it for 12v on ignition and it is getting it.  I don't have the valet switch or hood pin switch connected.  What am I missing?  I'm wearing out the plugs with all these connections/disconnections.

 

 

 

Login to reply View 1 answer(s)

21/08/2019

 Ford joseph Gagliardi (130Pts.)

0

red led stays on

tryed to program my evo all to my 2016 f150 with standard key when i hold program button in and plug in 4 pin data link plug red led comes on and stayes on no matter what you do until you unplug everything then it goes out this was a plug and play install with t harrness tryed reprograming module with my fortin flashlink 4 but still same issue
Login to reply View 1 answer(s)

28/10/2017

 Ford Joshua Clinard (130Pts.)

0

2010 Fusion. Getting solid RED LED but no yellow LED when in on position.

to start off im not really a car guy but this seemed pretty easy but anyways i just went to install the EVO-FORT1 into my 2010 Ford Fusion Sport and i put the data pin in and get the solid blue LED then go back and plug the red plug in and get the solid red LED. after all of that i go to put the key into the on postion but it stays solid red. i am asummng that it has something to do with the other plugs that has all the wires on the end?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue