Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

I bought a car that doesn’t have a remote

I just bought a vehicle with a evo all remote start already installed but no remotes. What do I need to do to get remotes and what is need to use my smart phone?

01/08/2024

Ford Djdrew (130Pts.)

0

Flash link eco all

Can I use flash link while the Evo All l is still plugged into my car or do I need to disconnect it all, and if I disconnect will I have to reprogram the keys again. I’m trying to install car link 6

0

Please reset the DCryptor's Limit. Model: EVO-ALL, Date: 12/2021, SN: 001A07 333332

Please reset the DCryptor's Limit. Model: EVO-ALL, Date: 12/2021, SN: 001A07 333332 I cannot program the module when the limit reached.

28/05/2024

Ford G M (14910Pts.)

1

2023 Ford Raptor (for reference)

For reference...On the 2023 Raptor, the CAN wires were in the left threshold, under the large black connector. The rest are all like the F-250...

26/04/2024

Ford G M (14910Pts.)

0

2023 ford ranger

Good evening. The 2023 Ford Ranger does not have a factory-installed remote engine start on the monitor. What should we do?

0

EVO-ALL WILL NOT PROGRAM WITH THE 2 KEY SET UP

I HAVE A 2013 FORD EDGE KEY START VEHICLE THAT WILL NOT PROGRAM WITH THE 2 KEYS. I'VE TRIED IT SO MANY TIMES. IS THE MODULE SET UP RIGHT? WHEN I GET TO STEP #8 THE LED'S DON'T FLASH I'M USING A {THAR-FORD1] HARNESS. S/N 001A07270913 THANKS.

3

2007 Ford Mustang EVO-ALL 1 Key programming

I'm having an issue with the single key programming of an EVO-ALL in a 2007 Ford Mustang. I get to the fourth step, where you turn the key forward and the blue LED is supposed to flash, however it does not flash for me, rather it just shuts off. When i turn the key off, it turns back on solid blue. I've verified all my connections about a hundred times, swapped out the EVO-ALL's, made sure my remote starter module is programmed correctly, so any help would be appreciated.

0

Evo All as bypass on an Avital 4105L

I made the entire connection of the "Evo all" as a bypass on an Avital 4105L and it doesn't work, I don't know what could be wrong, I did the installation according to the guide.

1

Evo All as bypass on an Avital 4105L

I tried using Evo All as a bypass on an Avital 4105L and tried to start my 2005 F-150 with the oem control and it didn't start, only started with the Avital control

0

EVO-ALL WILL NOT PROGRAM WITH THE 2 KEY SET UP

I HAVE A 2013 FORD EDGE KEY START VEHICLE THAT WILL NOT PROGRAM WITH THE 2 KEYS. I'VE TRIED IT SO MANY TIMES. IS THE MODULE SET UP RIGHT? WHEN I GET TO STEP #8 THE LED'S DON'T FLASH I'M USING A {THAR-FORD1] HARNESS. S/N 001A07270913 THANKS.

1

Evo All as bypass on an Avital 4105L

I tried using Evo All as a bypass on an Avital 4105L and tried to start my 2005 F-150 with the oem control and it didn't start, only started with the Avital control

0

D2D or W2W Fortin EVO All with FORT1 T-Harness and AVITAL 4105L for 2011 F-150

Hi, I purchased the THAR-FORT1 Kit which comes with the EVO ALL and FORT1 T-Harness. I also purchased the FlashLink updater and will set the EVO ALL to D2D. I would like to pair all of this with an Avital 4015L remote starter for my 2011 F-150 (I do not want to use the factory remote start protocol as my truck doesn't have power locks). I would like to only use the D2D cable to connect to the Avital 4015L in order to cut down on wire clutter. I would like to know if the D2D cable is the only cable I need to connect between the these two. I was looking at the wiring diagram for the EVO ALL with the FORT1 T-Harness and on the left side of the remote starter every cable is optional if D2D is used but on the right side there is parking lights which I don't care for so I wont be hooking up and Ignition. Doesn't the ignition communicate through D2D? https://fortin.ca/download/94881/EVO-ALL_IG_RTA_BI_FOR-FSERIES-2011-2016_KEY80bits_D_94881.pdf Wanted to know if I am on the right track here before I start the install. Thanks!

0

D2D or W2W Fortin EVO All with FORT1 T-Harness and AVITAL 4105L for 2011 F-150

Hi, I purchased the THAR-FORT1 Kit which comes with the EVO ALL and FORT1 T-Harness. I also purchased the FlashLink updater and will set the EVO ALL to D2D. I would like to pair all of this with an Avital 4015L remote starter for my 2011 F-150 (I do not want to use the factory remote start protocol as my truck doesn't have power locks). I would like to only use the D2D cable to connect to the Avital 4015L in order to cut down on wire clutter. I would like to know if the D2D cable is the only cable I need to connect between the these two. I was looking at the wiring diagram for the EVO ALL with the FORT1 T-Harness and on the left side of the remote starter every cable is optional if D2D is used but on the right side there is parking lights which I don't care for so I wont be hooking up and Ignition. Doesn't the ignition communicate through D2D? https://fortin.ca/download/94881/EVO-ALL_IG_RTA_BI_FOR-FSERIES-2011-2016_KEY80bits_D_94881.pdf Wanted to know if I am on the right track here before I start the install. Thanks!

2

Evo All and RF Kit with Aftermarket Power Locks

Hey guys I got another quick question, I purchased the EVO All, THAR-FOR1 T-Harness and RFK442 RF Kit which I will be installing soon for remote start functionality. So my 2011 F-150 did not come with power locks so I wired up a relay with a momentary switch a few days ago which is working well so far (see link for wiring diagram below). https://www.caraudioforumz.com/attachments/car-alarm-mobile-security-85/14792-wiring-diagram-aftermarket-door-locks-trim.jpg My question was, would it be ok to hook up the lock pin A19 and unlock pin A5 on the EVO All (see Fortin wiring diagram below) to pin 85 and 86 which go to the momentary switch (see other wiring diagram). https://fortin.ca/download/94891/EVO-ALL_IG_RTS_BI_FOR-FSERIES-2011-2016_KEY80bits_D_94891.pdf My thought process here was that say for example, I click lock on the RF Kit which would send the command to the EVO All and then the EVO ALL would send voltage to the relay and finally the door will lock? Did I get this right? What's confusing me is why a diode is needed in that orientation, seems like it will be blocking the lock signal? Thank you so much!

2

Evo All and RF Kit with Aftermarket Power Locks

Hey guys I got another quick question, I purchased the EVO All, THAR-FOR1 T-Harness and RFK442 RF Kit which I will be installing soon for remote start functionality. So my 2011 F-150 did not come with power locks so I wired up a relay with a momentary switch a few days ago which is working well so far (see link for wiring diagram below). https://www.caraudioforumz.com/attachments/car-alarm-mobile-security-85/14792-wiring-diagram-aftermarket-door-locks-trim.jpg My question was, would it be ok to hook up the lock pin A19 and unlock pin A5 on the EVO All (see Fortin wiring diagram below) to pin 85 and 86 which go to the momentary switch (see other wiring diagram). https://fortin.ca/download/94891/EVO-ALL_IG_RTS_BI_FOR-FSERIES-2011-2016_KEY80bits_D_94891.pdf My thought process here was that say for example, I click lock on the RF Kit which would send the command to the EVO All and then the EVO ALL would send voltage to the relay and finally the door will lock? Did I get this right? What's confusing me is why a diode is needed in that orientation, seems like it will be blocking the lock signal? Thank you so much!

1

2018 Ford Edge PTS Evo All T Harness

Hello, I have the Evo All W/ Evo Start in my 2018 PTS Ford Edge, looking through the menu options in flash, under SPECIAL OPTIONS i am wondering what

E1 GPS I/O, 

E3 ODB INFO are used for ?

AS ALWAYS, THANK YOU ALL !!!!

01/12/2023

Ford G M (14910Pts.)

1

2019 FUSION

There was a broken wire in the underwing connector going to the underhood button. We fixed it and the remote start worked. Thanks for support.

29/11/2023

Ford G M (14910Pts.)

0

2019 FUSION won't start and flashes 4 times

29/11/2023

Ford G M (14910Pts.)

0

2019 FUSION won't start and flashes 4 times

0

Flash Reset on EVO-ALL SN# 001A07472786

Could I please get a flash reset on an EVO-all that will be transferred from a Ford F-150 to a Ford Escape, SN: 001A07472786. Thanks in advance.

0

My 17 transit starts when red connecter plugged in

17 ford transit, evo all ver 71.52. service # 001a06761904. this was purchased from 12v solutions and havent been able to help with my issue. intial harness install and module programming went well. when i installed the cl6 smartphone app module, the vehicle started once from the phone app then would not turn off from the app, or pressing brake. i had to disconnected all the connections on module. now, vehicle starts as soon as i connect red plug. b4 i return for a refund, thought id ask here

0

2015 f150 push button : eco-fort3 no power after months of use

I have it hooked up to a LinkR-lt2. Worked fine for months and suddenly stopped working. Evo all module not getting any power

0

2012 Ford Explorer EVO-ALL The engine won't start.

I installed EVO-ALL on a 2012 Ford Explorer.

The wiring diagram is on page 3 of #94851 (WIRING CONNECTION) and I have completed the wiring and key programming.

When I press the lock button on the key 3 times the ignition turns on but the engine does not start.Nor does the cell.The cell won't turn either.

 

SN:001A07465529

FIRMWARE VERSION 71.52

 

best regards

0

Programing evo-all in 2013 Escape

Trying to install an evo-all with the thor-for1 t harness into a 2013 escape with standardkey start. Just want the remote start feature. Evo module came from my sons infiniti g37x. It has been reflashed with flashlink to be installed in the escape. Concerning that the flask status bar never goes over 25% beofore it "comepletes" the flash. The module will not program to the car. With the standard 2 key programing, when I get to step 8 and press and hold the program button, the vehicel never starts and the bule and red leds come back on solid. If I try the Dcryptor medthod, with either key, the red led never goes out and yellow never comes one durring the key cycle steps. if I just plug the module in w/o holdong the program button, all the leds flask as if the module is not programed. As the thor-for1 did not come with a C plug, I took the ones from the infiniti harness. however I do not have a A plug either, but not sure that is needed...?

0

Programing evo-all in 2013 Escape

Trying to install an evo-all with the thor-for1 t harness into a 2013 escape with standardkey start. Just want the remote start feature. Evo module came from my sons infiniti g37x. It has been reflashed with flashlink to be installed in the escape. Concerning that the flask status bar never goes over 25% beofore it "comepletes" the flash. The module will not program to the car. With the standard 2 key programing, when I get to step 8 and press and hold the program button, the vehicel never starts and the bule and red leds come back on solid. If I try the Dcryptor medthod, with either key, the red led never goes out and yellow never comes one durring the key cycle steps. if I just plug the module in w/o holdong the program button, all the leds flask as if the module is not programed. As the thor-for1 did not come with a C plug, I took the ones from the infiniti harness. however I do not have a A plug either, but not sure that is needed...?

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue