Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

2022 Nissan Armada restarts on its own after 5 seconds after turning off!

The car starts fine now with the remote start. But after turning the car off using the button on the dash, the car restarts on it's own after about 5 seconds. Then will turn off and stay off after pushing the dash button again. And now I also have a key fob error on my screen.

0

Key System error when manually starting with fob. 2019 civic

Evo one, with Hon 7 harness. Some times, not every time, I will get an error with Keyless system error when starting the car normally. This error also pops up after I get into ready mode as well.

0

After DCrypting remote start, why does my key no longer work on its own to start the car?

(key-to-start) Hooked up the T-Harness and did first module programming, it started fine with the key. Unhooked module and had to start car to go get computer because I forgot it. It started fine again and got me home. After running it through DCryptor program and hooking it back up I tested the remote start, that has worked fine too. But now my key wont start the car, it only turns it on and I can only remote start it. Tripple checked and everything is plugged in all the way and in the right places. What is the issue?

0

immobilizer system service required error after RFK kit install - car will no longer start with original key

Remote start was programmed and worked perfectly, however the takeover sequence only worked by pressing brake and restarting the car with original key. I just installed the RFK912 and progammed it corectly, the car worked fine starting from the rf remote and original remote. The car both remote started and then after shutting down started normally with the original fast key. The same night, after starting with the RF key and shutting down pressing the break, the car no longer starts with the original key and shows the immobilzer system service required fault. I can still remote start the car but cant use the original remote to start and drive away. after removing the evo-all - the car shows the same fault. It is stuck where it is. i tried to use teh dcrypot but it needs resetting - i want to reflash the dcryptor and try starting again. SN 001A07140493 the car is MITSUBISHI OUTLANDER 2014 EURO

0

2016 CHRYSLER 200 AND EVO-ALL - EARLY SHUTDOWN AND "SERVICE KEYLESS SYSTEM" ERROR

I installed the Evo-All with the T-Harness into my 2016 Chrysler 200 (push-to-start) over the weekend.  I did flash the unit beforehand with the options as indicated in the instruction manual and updated the software to the 74.[23] level recommended in the instructions.   I did NOT connect the MUX wire to the parking lights, as I am not interested in the parking light functionality. 

Programming and key decryption went entirely according to the book, and the vehicle remote-started immediately upon the initial test without difficulty.  I have also integrated a Crimestopper Teleconnect into this installation, and the smartphone app starts the vehicle, shuts it off, and lock and unlocks the doors as expected.

However, I have a few issues and I'm hoping for some insight into remedying them:

1)  The electronic driver display in the vehicle reads "Service Keyless System" immediately after the vehicle starts.  This error clears after a few seconds, but remains resident in the vehicle's memory.  This happens upon each start.

2)  The vehicle will initially start and then shut off after a few seconds.  Then it re-starts itself a few seconds later and runs for five minutes, and then shuts off.  The options flashed to the Evo-All call for it to run for 15 minutes.

3)  Attempts to re-start it are successful, but will run it for three minutes before it shuts off.

Obviously, I messed something up.  Your insights are appreciated.

0

2016 Chrysler 200 and Evo-All - Early Shutdown and "Service Keyless System" Error

I installed the Evo-All with the T-Harness into my 2016 Chrysler 200 (push-to-start) over the weekend. I did flash the unit beforehand with the options as indicated in the instruction manual and updated the software. I did NOT connect the MUX wire to the parking lights, as I am not interested in the parking light functionality. Programming and key decryption went entirely according to the book, and the vehicle remote-started immediately upon the initial test without difficulty. I have also integrated a Crimestopper Teleconnect into this installation, and the smartphone app starts the vehicle, shuts it off, and lock and unlocks the doors as expected. However, I have a few issues and I'm hoping for some insight into remedying them: 1) The electronic driver display in the vehicle reads "Service Keyless System" immediately after the vehicle starts. This error clears after a few seconds, but remains resident in the vehicle's memory. This happens upon each start. 2) The vehicle runs for five minutes and then shuts off. The options flashed to the Evo-All call for it to run for 15 minutes. 3) Attempts to re-start it are successful, but will run it for three minutes before it shuts off. Obviously, I messed something up. Your insights are appreciated.

0

2016 Chrysler 200 and Evo-All - Early Shutdown and "Service Keyless System" Error

I installed the Evo-All with the T-Harness into my 2016 Chrysler 200 (push-to-start) over the weekend. I did flash the unit beforehand with the options as indicated in the instruction manual and updated the software. I did NOT connect the MUX wire to the parking lights, as I am not interested in the parking light functionality. Programming and key decryption went entirely according to the book, and the vehicle remote-started immediately upon the initial test without difficulty. I have also integrated a Crimestopper Teleconnect into this installation, and the smartphone app starts the vehicle, shuts it off, and lock and unlocks the doors as expected. However, I have a few issues and I'm hoping for some insight into remedying them: 1) The electronic driver display in the vehicle reads "Service Keyless System" immediately after the vehicle starts. This error clears after a few seconds, but remains resident in the vehicle's memory. This happens upon each start. 2) The vehicle runs for five minutes and then shuts off. The options flashed to the Evo-All call for it to run for 15 minutes. 3) Attempts to re-start it are successful, but will run it for three minutes before it shuts off. Obviously, I messed something up. Your insights are appreciated.

0

CHRT6 in 2015 Chrysler 200 Push-to-start service key fob system

I just finished installing the CHRT6 in my 2015 Chrysler 200 that has push to start. It starts fine, but when it does a message comes up in the gauge cluster saying "Service Key Fob System" and then when I get in and put it into gear the head lights, fog lights, and parking lights all flicker on and off twice. Is this normal? If not how can I fix it? Thanks.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue