Clear All

Search

Looking of our top participants?

See users

Couldn’t find what you were looking for?

Ask us a question

03/01/2023

Chevrolet Ryan McNulty (130Pts.)

Installed Evo on 2015 Silverado HD diesel and followed instructions, but remote start not working

2015 Silverado 3500 Duramax. Installed everything properly and followed all directions. Even watched install video to make sure. Have all settings set to factory, expect for diesel mode and 20s crank. Doors unlock when evo module is plugged back in after decryption, but remote start does nothing. I know the module is communicating because when removed the truck goes into theft protection mode and will not start. Please help.

chevy

2500hd

remote-start-not-working

30/09/2022

Chevrolet Clint Hembree (130Pts.)

Where is the starter wire on a 2002 Silverado 2500 duramax?

Trying to get my remote start system up and going by the diagrams and pictures do not show which wire is the starter wire under my steering column.

remote-start

silverado

2500hd

20/09/2022

Chevrolet julio pelayo (1650Pts.)

2003 Chevrolet Silverado 2500hd, doesn't option A7 need to be on for remote shut down and take over?

Guide says option A7 off, just want to make sure also option A11 if truck has factory hood pin switch i turn it off? If I add pin switch turn it on? Can you tell me what options i need on for 2003 Chevrolet Silverado hd diesel? Installing viper remote start, what protocol do I need?

2500hd

chevy

silverado

09/04/2022

Chevrolet ignacio oneil (130Pts.)

Fortin EVO GM4 on Silverado 2500HD W/T will not start engine but controls door opening and closing

I need help with this... I have programmed and installed fortin evo GM4 in my chevy 2500 11”, the blue light comes on every time I press the 3X control but the engine does not start… so what could it be??

chevy

2500hd

03/02/2021

Chevrolet Andrew Peckham (170Pts.)

2008 Silverado 2500hd starts fine with the 3x lock button, if started with key I get a security light

I am using the EVO-GMT4 which comes with the T-harness. 2008 2500HD 6.6 Duramax WT with standard key. All programing went fine, after initial installtion had a fuse blow - under hood DIS 2.5A fuse - replaced and system works with 3x lock button on factory remote. If I key start the truck I get a security light on the dash, stays on solid the entire time. Truck runs fine just has the annyoing light on the dash. Have not pulled the code for the light yet as it goes out if I start with the 3x lock feature. Any suggestions?

03/02/2020

Chevrolet Alek Ipatenco (160Pts.)

Evo-All sending ignition on thru data to external remote start/alarm, 2006 Silverado 2500HD

I have installed an Evo-All with Crimestopper SP-502 alarm/remote start system and the Evo-all is sending a continuous ignition on thru data signal to the SP-502 unit. This is verified by the key icon on the alarm remote and also the trouble code on the SP-502 when trying to remote start the vehicle. The Evo-All is programmed with firmware version 70.18. The wires are connected per guide number 61111 with the exception for trunk release (A13) which is N/A and Hood Status (A15) which is also N/A for this vehicle. The Evo-All is programmed per guide number 61111. The wiring from the Crimestopper SP-502 was connected to the Evo-All as per guide number 61111 and the remaining wires on the SP-502 were installed per the SP-502 installation manual. The doors lock and unlock, but the continuous ignition through data from the Evo-All is preventing the SP-502 from setting the alarm, or remote starting the vehicle. I have verified each wire connected is correct per the manuals and wirecolor, vehicle specific instructions. What issues would cause a continuous "ignition on through data" signal from the Evo-All? Thanks in advance for your help!

ignition-through-data