Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

Jerry Thor

À rejoins en date due:

May. 5, 2017

Points

410

Commentaire(s)

9

Questions votée(s)

0

Réponses votée(s)

2

Votes positifs

0

Votes contre

2

Votes reçus

0

Votes négatifs reçus

0

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

0

Parking light not flashIing when the alarm of the Evo is triggerd.

I have this alarm install for 2 year now just notice today at work when my car alarm was triggerd the parking light was not flashing. Eveything seem to be working fine, the parking lights flash when arm/disarm and when the remote start too. So I don't know I'm at lost here. What could of happen? 002B07164993

0

Using Drone app to lock/arm car and when using the OEM remote key fob to unlock alarm trigger when opening the door

So I finally got the Evo-one/Drone to work with my 2005 Honda Pilot over the weekend. However while using the Evo-one/Drone app to lock/arm the car and when I use the OEM key remote fob to unlock while opening the door trigger the alarm. When the alarm is trigger can't use the OEM key remote to disarm, only Drone app that was use to arm the car will disarm it. While I use the OEM key remote fob to lock/arm the car, I can use the Drone app to unlock/disarm the car and able to open the door without trigger the alarm. Is there a setting in the EVO-ONE that I need to change in order for the alarm to turn off when I use the OEM remote to unlock/disarm the car when the Drone app is use first to lock/arm the car? Or is that not possible

0

Evo One and Drone DR 3400 would not remote Start 2005 Honda Pilot only lock/unlock

 

I follow the Guide # 27481 Connection 2 , Programming 2 , also did lock/unlock, Horn, disarm, GWR to Key Sense  and foot brake wires. When using the Drone app to start the car it would not start or do anything at all, no parking light flash, no light from the 3 LED beside the red light by the yellow wire cut loop.

When the lock/unlock  on the Drone app is press the door would  lock/unlock/disarm parking light flash and still no start. I have reset and master reset the module, reprogram, check all the  wires and relocate the ground wire still won't start or hear the relay.

Did I not program it right or am I missing some wires connection?

Bypass Firmware version: 73.26

Remote Starter Firmware version: 0.50 Drone


What I have hook up

(6-PIN) POWER CONNECTOR

(+) Ignition Pink to Black/Yellow car (+) Ignition

(+) Starter Yellow to Black/White car (+) Starter

(+) Accessory Orange to Yellow car (+) Accessory

(+) Parking Light White to Red/Black car (+) Parking Light

(+) 12v Red to White car (+) 12v


(6-PIN) BYPASS RELAY

D6 White/Red to Pink (cut) at Ignition barrel going out  pin 5 Security Light

D4 White/Green to Pink (cut) at Ignition barrel side of pin 5 Security Light  


(20-PIN) SECONDARY CONNECTOR

A1 to (+) Ignition

A2 to (-) Black/Orange car Lock

A3 to (-) Blue/Orange car Unlock

A6 to (-) Pink/Black Disarm

A7 to (-) lt. green/blue Horn

A8 to blue/black Key Sense

A10 to Red/Green Data Pin2

A11 to (+) White/black Brake wire


Would it be better to used RF kit before the Drone, seem the Alarm is working but not the remote start.  

Well, right now the Evo one is out of the car so I won’t be able to go at it until the weekend the only time I’m free. Any help would be great or  anyone who have done 2005 Honda Pilot  Evo One with Drone with some input how you got it to work would be great too.


Thank you,

0

2005 Honda Pilot Evo one wires

I'll be doing this installing this weekend and I got most the wire down. Need help with some of the wires. On the 20-pin connector A8 (-)DK.Blue wire look like I have to connect it to Key Sense (Blue/Black) Ignition harness is that correct? For the arm/disarm I only see A6 (-) Orange for disarm to pink/black behind glove box, green connector but what wires on the 20-pin connector would I use for the arm or do I not need to and will it still arm? The hood, door and trunk status would I isolate them with diode connect to A15 (-) pink/black wire or other wire I can use? For the door trigger would I wire all 4 door or just one for all the door status. I would be adding a shock sensor with the evo one and I would be using Drone Mobile DR-3400 for this install.

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer