Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2011 Scion xB won’t remote start EVO ONE

No immobilizer, did not connect light blue/ black wire, module programs ok by letting go of button on blue, and the flashes blue rapidly after turning key to on. 
 

    ​I already tried connecting the immobilizer wire & programming again. I already tried programming using red & blue light but that won't program. Using Fortin guide #23001. Not "G" key. Verified no immobilizer/chip on key. Won't remote start with lock 3 times on key. Won't remote start with the MyCar app module.

0

2011 Scion xB won’t remote start EVO ONE

No immobilizer, did not connect light blue/ black wire, module programs ok by letting go of button on blue, and the flashes blue rapidly after turning key to on. 
 

    ​I already tried connecting the immobilizer wire & programming again. I already tried programming using red & blue light but that won't program. Using Fortin guide #23001. Not "G" key. Verified no immobilizer/chip on key. Won't remote start with lock 3 times on key. Won't remote start with the MyCar app module.

0

unable to program evo one module for 2016 scion im ?

blue light solid while red light flashes then i tried programing again and then the only light that flashed was the red one

0

unable to program evo one module for 2016 scion im ?

blue light solid while red light flashes then i tried programing again and then the only light that flashed was the red one

0

USDM 2013xB Canbus Door lock control?

I recently got my evo one today, and installed it after some back and forth with the firmware and the updates. It starts using the lock-unlock-lock feature (did this so that the alarm is in a disarmed state when the engine starts, so no need to splice into key sense)  However, when I start the car using the remote, nothing happens when i go to try and unlock the doors using the remote. I know that the car ignores the remote with the engine started, and I can see that the evo one is recieving the lock and unlock commands from the vehicle(can see blue light blinking with each key press ) but I'm unsure if the doors are supposed to unlock with from the can hi and can lo connections, or do i have to splice into the door lock and unlock wires in order for the  door to unlock? 

0

USDM 2013xB Canbus Door lock control?

I recently got my evo one today, and installed it after some back and forth with the firmware and the updates. It starts using the lock-unlock-lock feature (did this so that the alarm is in a disarmed state when the engine starts, so no need to splice into key sense)  However, when I start the car using the remote, nothing happens when i go to try and unlock the doors using the remote. I know that the car ignores the remote with the engine started, and I can see that the evo one is recieving the lock and unlock commands from the vehicle(can see blue light blinking with each key press ) but I'm unsure if the doors are supposed to unlock with from the can hi and can lo connections, or do i have to splice into the door lock and unlock wires in order for the  door to unlock? 

1

frs oem remote

working on a 2016 scion frs. using evo all with a compustar cm7000. evrything program correctly and works from compustar remote. and I have option C1 on as per the manual but the OEM remote does not activate the compustar alarm, and not sure if supported but 3x lock does not work either.\ edit: put everything together and now it starts but the cars shuts off after a couple seconds. locks still work and tach programs okay. i also noticed on the installation it says to interupt the security light. there is no wire in that location given in the installation manual

1

frs oem remote

working on a 2016 scion frs. using evo all with a compustar cm7000. evrything program correctly and works from compustar remote. and I have option C1 on as per the manual but the OEM remote does not activate the compustar alarm, and not sure if supported but 3x lock does not work either.\ edit: put everything together and now it starts but the cars shuts off after a couple seconds. locks still work and tach programs okay. i also noticed on the installation it says to interupt the security light. there is no wire in that location given in the installation manual

1

frs oem remote

working on a 2016 scion frs. using evo all with a compustar cm7000. evrything program correctly and works from compustar remote. and I have option C1 on as per the manual but the OEM remote does not activate the compustar alarm, and not sure if supported but 3x lock does not work either.\ edit: put everything together and now it starts but the cars shuts off after a couple seconds. locks still work and tach programs okay. i also noticed on the installation it says to interupt the security light. there is no wire in that location given in the installation manual

29/12/2015

Scion losmt2 (380Pts.)

0

2015 Scion FRS (manual) push to start not programming

I go through all the steps and but but when I connect the EVO ONE the second time to read the sample of the immobilizer I get:

The module was not able to sample the vehicles immobilizer data.

I have tried multiple times and sometimes after I start the car the red light doesn't blink and sometimes the red light blinks while the blue led is steady on then the blue led flashes then the red and yellow alternate. This makes it take longer but I have had it go through the regular steps and still the Dcryptor part is not getting my car's data.
 

 

 

29/12/2015

Scion losmt2 (380Pts.)

0

2015 Scion FRS (manual) push to start not programming

I go through all the steps and but but when I connect the EVO ONE the second time to read the sample of the immobilizer I get:

The module was not able to sample the vehicles immobilizer data.

I have tried multiple times and sometimes after I start the car the red light doesn't blink and sometimes the red light blinks while the blue led is steady on then the blue led flashes then the red and yellow alternate. This makes it take longer but I have had it go through the regular steps and still the Dcryptor part is not getting my car's data.
 

 

 

0

Could you please reset my evo all flash limit S/N 001A06 462499

0

2015 Scion xB Evo-One, no transponder

Installing an Evo One for remote start with t-harness Toy1, vehicle has canbus, but is not equipped with a immobilizer system. Installed per guide #92261, but am not hung up on programming/key sense. Obviously I am going to use a different sequence because it will not get to the flashing blue led, there is no immobilizer (verified key has no transponder chip). Is there another quide for 2015 xB with Canbus but no immobilizer?

0

Will the EVO ONE work on my 2016 Scion tC with push button start?

Hi, I see the EVO ONE should work for my 2016 Scion tC but the trim level states standard key. The 2016 model only came with Push to start. No manual key option. Will this work? If so, which T harness should I use? Car is also manual if that matters. Thanks

0

Ready Mode turns off when closing the door on a manual 2013 Scion FRS Key Start

After wiring everything correctly and triple checking all the wirings I can control lock, unlock and even engine shutoff using the mobile app but for some reason after putting the car in ready mode and closing the door the engine shuts off, and when trying to start it again using the mobile app it starts for half a second then shuts off I tried resetting the module and reflashing multiple times and even went back to the frimware recommended in the guide but now it's saying that the decryptor's limit has been reached... and it's still giving me the same errors SN: 002B04 664699

0

EVO-ONE + START-2 in 2012 Scion IQ app door locking does not work but unlock does

I have an EVO-ONE with T-Harness and EVO-START-2 RF kit installed. The door lock data is connected from EVO-ONE to vehicle harness. The Android app communicates with the car. Using the app to REMOTE UNLOCK the car works fine and flashes the parking lights The LOCK command from the app flashes the parking lights, but DOES NOT REMOTE LOCK the car. Any ideas?

0

Remote not working to start or lock/unlock a Scion TC 2016

Just put new batteries in and remote doesn't seem to click in. Blue light flashes, then get a red at the end. Can't lock or unlock the car with remote.

0

Alarm setting off

I installed the EVO ONE without T-Harness and RFK411 on a 2014 Scion XD (with standard key). Sometimes after remore start, when the door is opened the alarm is set off and the remote start is halted. Option D2 was inititially turned off.  I turned it on and though it improved quite a bit, it still happens every now and then.  The system is wired and configured per Guide # 102241.  Any help would be greatly appreciated.

0

trouble getting a 2016 scion ia to remote start reliably

2016 scion ia remote starting, do i need too wake up the light circuit? used an ar35 as per the instructions. also which firmware should i use with this particular model evo-one, t harness, ar35, with the 62-rw were the parts used, all other functions on the remote work flawlessly

0

Get a signal but won't start

Hello I installed my Evo one about 2 year ago on my scion FRS 2013 it always worked but now for some reason it won't work after the night if I try it when at work it work but when I get home and set it up in the morning it get signal and parking light flashes but the car won't start... I have to get in the car and it work with the key.

0

2009 SCION XB RX AND TX CONNECTOR

I TRY USING THE 2011 + SCION XB WIRING DIAGRAM AND IT DOENST WORK I TRYING TO WIRE FOR THE 2008 SCION XB WIRING DIAGRAM AND I CANT FIND THE RX AND TX THERE NO CONNECTOR NEAR THE IGNITION THAT HAS THE 7 WIRE.

0

2014 Scion Xb Evo Ride

I do not have the IMO and IMI wires at the ECU as stated in the connection 17 diagram. Can I wire this in a different configuration to function similar? Or am I looking to purchase a different product? Do I need to wie in the Key sense?

25/12/2018

Scion D L2 (130Pts.)

0

Please help with installing EVO-All Kit for my 2016 Scion iA

I received the EVO-All KIT and already flashed the newest firmware. I just want it to be a standlone with 3 locks remote start function to work. I bought the THAR-MAZ1 to my life easier. I've read the diagram and my understanding is we have to do some wire tapping in order to make everything work. Is there a way for me to make it a standlone with 3 locks remote start to work without doing any wire tapping ?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer