English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

08/05/2016

 GMC timmerk (950Pts.)

2

Is there a ground while disarmed output on the EVO-ALL?

Is there a ground while disarmed output on the EVO-ALL? And if so, does the EVO-ALL monitor the CAN bus so that if I disarm the alarm with the factory fob, the ground while disarmed output is triggered to reflect the OEM status change? Thanks!
Connectez-vous pour répondre Voir 1 réponse(s)

08/11/2014

 GMC nathan herron (150Pts.)

2

Programming -Yellow led stays on, ignition is off. Whats it mean?

Hi, I just bought an Evo-One and the flashlink updater. Very nicely made :).   I used guide # 23261, and wired my 2006 GMC Sierra 1500 (page 3) as instructed. On page 7, everything went fine up until turning the ignition off- the yellow led stays on.   I'd just like to get a clear answer as to what my options are/what I'm missing. I'm not being a pain, just would like a little help instead of being hung up on. Like- should I cut the wire loop, what does the yellow led mean, is there a certain evo-one update I should flash?   Or is guide 23261 not correct for my vehicle, a 2006 GMC sierra 1500?   Thanks a ton in advance, Nathan
Connectez-vous pour répondre Voir 1 réponse(s)

12/09/2021

 GMC Mundher Sulaiman (170Pts.)

1

Car goes off after 20 seconeds the goes on.

I have Yukon 2005, I install on it EVO All + excalibur 70X when I start it by remote (OEM,Excalibur additional remote or from door lock switch) a car still working for 20 seconds then goes off and automatically started again, This problems stay for 3 times then a car switched off, I make reflash a Fortin but same issue, I replace it with Excalibur 70B also same issue, I checked all wiring every thing in good condtion. But if I start a car by Key it's working fine without any issue. This issue suddnly happend with me started before 3 weeks from now but before it's working fine. Car battery is new I replace it before 5 months. There is any thing need to check it more? please I need help, also I install same devices for many cars I don't face same this issue with any car excepte my car. Please check this issue on YouTube I uploaded a video for this issue: https://www.youtube.com/watch?v=qFL4xSWzhvM
Connectez-vous pour répondre Voir 1 réponse(s)

21/04/2018

 GMC Carlos Paige (750Pts.)

1

Evo One programming key bypass. Does not finish step 4.

I had an Evo One install in my 06 trailblazer. I replaced it, and installed it on an 05 GMC Envoy XL. I did a master reset on starter and bypass, using recommended updates. When trying to program with the button pressed, I plug in the six pin connector to get to the blue led, I then plug in the remaining connectors. Turn the key to the on position the blue light go out but no other lights come on. If I turn the key back to the off position the blue light return. I'm only using all wires from the 6 pin connector. The data, the park light, the horn, the brake, and the A1 ignition wires off the 25 pin connector. And antenna and valet button connection. All wires have continuity though connector and wires. Tried a spare Evo One that had on hand, got the same results.
Connectez-vous pour répondre Voir 1 réponse(s)

21/09/2017

 GMC Daniel Waslenko (2650Pts.)

1

Remote start keeps shutting off

I installed a remote start on a 2007 GMC Sierra Classic diesel (2006 electronics). Evo-All with an Avital 4105 remote start. Lock, and unlock work fine 100% of the time. When I set the 4105 to virtual tach, it will remote start and stay running only if the engine was already warm. If it is cold it will start and after 20 seconds shut off and restart itself. I set the unit to tach, and it shuts off immediately. If tach is supported over data, then why does it shut off right away? Also what would cause the remote start to shut off after 20 seconds and keep restarting itself if i don't use the regual tach feature? I have the data on F3: D2D. I have used this unit combination on over 50+ vehicles without an issue, so what is giving me the problem?
Connectez-vous pour répondre Voir 1 réponse(s)

10/01/2017

 GMC Derek Hodgson (190Pts.)

1

2011 GMC Sierra 1500 Remote Start Lock X6 WHY?

I installed my GMT4 System and was super easy to install and program BUT I have to press the lock button on my oem remote six times not just the three as described. Also can I stop the horn from honking all six times when using remote start option? And Last but not least how do I know from 800ft away if my truck has stopped after the six pushes of the lock button. Really need to get this to three times lol.
Connectez-vous pour répondre Voir 1 réponse(s)

10/11/2016

 GMC Devon Gurrola (140Pts.)

1

2017 GMC Terrain All Features Don't Work

Unit is on 70.24 heated seats don't come on, but rear defrost does and power liftgate does not work. Master reset unit, reprogrammed, same thing.
Connectez-vous pour répondre Voir 1 réponse(s)

03/09/2016

 GMC timmerk (950Pts.)

1

Where is EVO-ONE full install guide?

The Fortin website only lists: http://fortin.ca/download/21541/evo-one_ig_thr_bi_gm4_wddp_a_21541.pdf http://fortin.ca/download/59261/evo-one_ig_reg_bi_gm_silverado-sierra_2007-2014_a_59261.pdf for the EVO-ONE manuals for a 2008 GMC Sierra 1500, but these manuals are missing tons of information on most of the pins, like what output is the tach, what inputs are door lock/unlock, what is the starter input from a third party starter, etc. Could someone please point me in the right direction? Even better, maybe Fortin would want to update their website with the general manual that covers these missing connections.
Connectez-vous pour répondre Voir 1 réponse(s)

09/05/2016

 GMC Ernest Rogers (140Pts.)

1

2000 Gmc Sierra

I have a 2000 GMC Sierra. I downloaded the wiring on the Wirecolor.com. I have a Crimestopper Cool Start RS00-G5 and the INT-SL+ . I have a factory keyfob that I will do 3x Lock engine start. What do I need to wire up. Instructions are soooo confusing. I have factory door unlocks,and locks and lights on...Thats all I need . ADDING the engine start. I think I can use just the Data Link wire and and hook up a few wires and done. ( i have installed the RS00-G5 in my Cadillac Escalade....but I used an EVO-ALL , )
Connectez-vous pour répondre Voir 1 réponse(s)

06/05/2016

 GMC timmerk (950Pts.)

1

Will brake status work with truck off and no previous activity?

I will be installing the Advanced Keys Push to Start module in my 2008 GMC Sierra truck, and was reviewing different bypass/combo solutions to use with it. 

It looks like the EVO-ALL does the brake status by monitoring the CAN bus. Will the brake status work with truck off and no previous activity (i.e. no recent door unlock)? I need it to work because you must press the brake in order to push to start. However, the Advanced Keys people claim that a firmware update to the EVO-ALL stopped this from working while off:

http://www.advancedkeys.com/forum/viewtopic.php?f=4&t=968&p=2935#p2868

But then a Fortin rep said it still works, so I was wondering if anyone knew the definitive answer. Thanks!

Connectez-vous pour répondre Voir 1 réponse(s)

04/04/2016

 GMC steve m (1340Pts.)

1

2001 gmc sierra door locks

is there a bypass that does the door locks if not is there a diagram for door locks to hook to a relay
Connectez-vous pour répondre Voir 2 réponse(s)

04/04/2016

 GMC steve m (1340Pts.)

1

2001 gmc sierra door locks

is there a bypass that does the door locks if not is there a diagram for door locks to hook to a relay
Connectez-vous pour répondre Voir 2 réponse(s)

11/12/2015

 GMC Brandon Hurlbert (140Pts.)

1

the bypass module won't blink when I turn the key on to program , 2003 sierra 2500, remote starts then shuts off

I have a compustar CS800-S with a fortin INT-SL+, hooked it up and went through the program procedure and can't get the module to go to the key on LED blinking portion, it will start with the remote but shut off right away
Connectez-vous pour répondre Voir 1 réponse(s)

17/01/2015