Questions & Réponses

I have programmed and installed, the car when pre 3x lock start, led go red, after yellow, after stop engine and red flash 2 time yellow turn of, and retry automatically the second time to start engine, this run, red and yellow power on, after shut off nd red flash one time. What i need to do? What is the problem? Standard key.

https://www.youtube.com/watch?v=XOidPkUg9aY

I have programmed and installed, the car when pre 3x lock start, led go red, after yellow, after stop engine and red flash 2 time yellow turn of, and retry automatically the second time to start engine, this run, red and yellow power on, after shut off nd red flash one time. What i need to do? What is the problem? Standard key.

https://www.youtube.com/watch?v=XOidPkUg9aY

Installed an Evo-One and Fortin RF642W 2 way RF kit in a 2003 Buick Century. Followed "connection 1" and "programming 1" as stated to by this install guide. http://fortin.ca/download/23261/evo-one_ig_reg_bi_gm_j1850_b_23261.pdf

All wiring has been verified multiple times to be exactly what the install guide said to do...nothing more and nothing less.

When I try to remote start the car, via the 2 way remote, the car will power on but will not crank the starter at all. When I use the remote to kick the car into "idle mode", the car unlocks as it should but shuts off when I turn the ignition off to pull the key.

Bypass portion programmed fine....RF remote also programmed fine.

Literally, the only wires connected at the moment are what the install guide I linked above says.

Installed an Evo-One and Fortin RF642W 2 way RF kit in a 2003 Buick Century. Followed "connection 1" and "programming 1" as stated to by this install guide. http://fortin.ca/download/23261/evo-one_ig_reg_bi_gm_j1850_b_23261.pdf

All wiring has been verified multiple times to be exactly what the install guide said to do...nothing more and nothing less.

When I try to remote start the car, via the 2 way remote, the car will power on but will not crank the starter at all. When I use the remote to kick the car into "idle mode", the car unlocks as it should but shuts off when I turn the ignition off to pull the key.

Bypass portion programmed fine....RF remote also programmed fine.

Literally, the only wires connected at the moment are what the install guide I linked above says.

Vehicle is a 2005 Buick Rainier with standard key. Installed the EVO ONE (remote start firmware 0.44) and the OL-RF-52-SST about a year ago (May 2020). Everything worked OK. The truck had an engine failure and was in the shop for several months with the battery disconnected. When powered back up, the Omega RF remotes no longer work. OEM remotes work. I followed the directions for remote programming as listed below. My antenna LED is not lighting up at all.

The unit was intalled with a custom T-harness for power using OEM connectors and automotive-grade wire. The 30A inline fuse is good.The harness to the antenna looks OK. I verified the unit still has FW 0.44 via my Flash-Link 4 programmer.

Here's the process I tried to program the remotes:

Flash 0.44 into the remote starter and do the following to program:

- ign on off on, led on antenna will light up solid. 

- 4x on brake pedal. It should blink once with each brake press.

- Then send lock from each remote, should blink once again to confirm it programmed.

Vehicle is a 2005 Buick Rainier with standard key. Installed the EVO ONE (remote start firmware 0.44) and the OL-RF-52-SST about a year ago (May 2020). Everything worked OK. The truck had an engine failure and was in the shop for several months with the battery disconnected. When powered back up, the Omega RF remotes no longer work. OEM remotes work. I followed the directions for remote programming as listed below. My antenna LED is not lighting up at all.

The unit was intalled with a custom T-harness for power using OEM connectors and automotive-grade wire. The 30A inline fuse is good.The harness to the antenna looks OK. I verified the unit still has FW 0.44 via my Flash-Link 4 programmer.

Here's the process I tried to program the remotes:

Flash 0.44 into the remote starter and do the following to program:

- ign on off on, led on antenna will light up solid. 

- 4x on brake pedal. It should blink once with each brake press.

- Then send lock from each remote, should blink once again to confirm it programmed.

Vehicle is a 2005 Buick Rainier with standard key. Installed the EVO ONE (remote start firmware 0.44) and the OL-RF-52-SST about a year ago (May 2020). Everything worked OK. The truck had an engine failure and was in the shop for several months with the battery disconnected. When powered back up, the Omega RF remotes no longer work. OEM remotes work. I followed the directions for remote programming as listed below. My antenna LED is not lighting up at all.

The unit was intalled with a custom T-harness for power using OEM connectors and automotive-grade wire. The 30A inline fuse is good.The harness to the antenna looks OK. I verified the unit still has FW 0.44 via my Flash-Link 4 programmer.

Here's the process I tried to program the remotes:

Flash 0.44 into the remote starter and do the following to program:

- ign on off on, led on antenna will light up solid. 

- 4x on brake pedal. It should blink once with each brake press.

- Then send lock from each remote, should blink once again to confirm it programmed.

Vehicle is a 2005 Buick Rainier with standard key. Installed the EVO ONE (remote start firmware 0.44) and the OL-RF-52-SST about a year ago (May 2020). Everything worked OK. The truck had an engine failure and was in the shop for several months with the battery disconnected. When powered back up, the Omega RF remotes no longer work. OEM remotes work. I followed the directions for remote programming as listed below. My antenna LED is not lighting up at all.

The unit was intalled with a custom T-harness for power using OEM connectors and automotive-grade wire. The 30A inline fuse is good.The harness to the antenna looks OK. I verified the unit still has FW 0.44 via my Flash-Link 4 programmer.

Here's the process I tried to program the remotes:

Flash 0.44 into the remote starter and do the following to program:

- ign on off on, led on antenna will light up solid. 

- 4x on brake pedal. It should blink once with each brake press.

- Then send lock from each remote, should blink once again to confirm it programmed.

I do not see "remote start" mentioned in the features listed for this car for the Evo-One.

Does the Evo-One work as both the bypass and remote starter for a 2003 Buick Century?

Would it require more wiring than what is shown here(install #1 in the link)? https://fortin.ca/download/23261/evo-one_ig_reg_bi_gm_j1850_b_23261.pdf