Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Audi 2013 S4 DSG - Fortin ALL getting stuck on step 7 with 3 x red flashing lights

Just installed a Fortin ALL with the Audi T Harness on a 2013 Audi S4 DSG. UK right hand drive car. When I go to try and get the unit to read the key data I am just getting 3 red light flashes on step 7, everything is fine up until that point and the car operates as normal. When I then put the flashlink back onto the PC software it says invalid key data. Any ideas? I have checked all wiring, also checked status of CANBUS with zero issues showing so I know that wiring is good. Serial no for module is : 001A07445150

0

Invalid key data

When I am trying to do dcryptor it's saying invalid key data for Audi A4 2013 i tried so many times by resetting evo all but same result

0

key port works but only when t harness is unplugged

2012 a4 w/push to start will not start. fortin inicated the key port has to be functional in order for it to start. but the key port does not work unless the t harness is unplugged. I was unable to get any help from fortin when i called anyone else had this issue and how can i resolve. the install thus far has been easy , simply tapped the brake signal wire and can high and can low. when the evo is connected it does attempt to start the car meaning it flashes each of the three lights but never hear the starter engadge. updated firmware as requested previously by fortin. but when i called today fortin tech was no so eager to assist. said either the evo relays are bad or the t harness is bad. can i help with anything else. I indicated i would like assistance tryin to resolve. so im trying to work through the troubleshooting he offered but now will not answer the phone. any help would be greatly appreciated.

0

Can not proceed Page 6/10 (dcryptor programming procedure). when i apply the step 4 in page 6/10 the Blue LED turns off

I've updated module Evo-One for my Audi A5 2011 Gas with key-port before the installation and now can not proceed Page 6/10 (dcryptor programming procedure). when i apply the step 4 in page 6/10 the Blue LED turns off which makes unable to continue the step 5.

0

KEY BYPASS PROGRAMMING PROCEDURE 2/3 | 2016 Audi A6

On part 7 of the key bypass programming , the EVO ONE goes through the first light process correctly, the car ignition turns of and then on , then stays one and the lights on the EVO ONE go from cycling all 3 lights to just flashing red ~ instead of slowly yellow red ! Followed the regular installation instructions for the EVO one ! Checked over all the wires for solid connections ? Anyone have any trouble with a EVO one stand alone on a A6 key bypass steps ? Purple wire was cut !

0

Why does the 2014 Audi S4 not require key but 2015 does?

I am interested in purchasing an Evo-One for the 2015 Audi S4 Keyport but I am wondering why the install is more difficult than the 2014. Are you planning to introduce a new product that doesn't require the key for the 2015 or will this always require the key?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer