English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

19/11/2021

 Mazda joel rowe (130Pts.)

0

Cx5 key handoff - shuts off on door being opened

Engine shuts off on door being opened. What setting needs to be changed to allow key handoff? 2016 Mazda CX5 I'm using evo-all with maz1 t harness. Thanx
Connectez-vous pour répondre Voir 0 réponse(s)

27/01/2021

 Mazda ERIC DOMINGO (290Pts.)

0

2010 Mazda 6 Standard Key EVO-ONE - Dcryptor Step 5

Hello, For a 2010 Mazda 6 Standard Key (instructions https://cdn02.fortin.ca/download/80571/evo-one_ig_reg_bi_maz_6_2009-2013_key_a_80571.pdf), I can't get the Dcryptor process (specifically step 5) to work for the EVO-ONE. The unit was removed and reinstalled, and I reflashed and master reset the bypass (Flashlink recommended 7.44 and I followed the hold down prog button while connecting 6-pin, then hold down again until all LEDs cycle). When I get to step 5, both the yellow and red LEDs are on and the red LED never turns off to proceed to step 6. If I turn off the ignition, both yellow and red remain on. I have tried the 2 key method and it will not work either. I have resoldered the TX and RX lines on the transponder connector as well. The unit otherwise attempts to remote start the car, but the security light flashes quickly on the dashboard and remote start is not successful, then the parking lights flash 4x after the failed start. Any other suggestions?
Connectez-vous pour répondre Voir 1 réponse(s)

23/01/2021

 Mazda Hovhannes Hakobyan (350Pts.)

0

message "invalid key data" during dcryptor step

message "invalid key data" during dcryptor step mazda 6 2014 start\stop
Connectez-vous pour répondre Voir 1 réponse(s)

12/12/2020

 Mazda Ryan Smith3 (130Pts.)

0

Blinking amber light on start button 2016 CX-5

The module seems to work fine, I have completed every step in the installation guide. However, the start button does continuously blink amber/orange while the vehicle is running and does not stop until the engine is shut down. This only happens when started normally, not remotely. If I disconnect power to the EVO ONE, the car can be started just fine and there is no blinking light. I used the THAR MAZ 3 t-harness to install. I have been scouring the Mazda forums and have found no answer. Everyone says either replace the fob batteries (I replaced them) or visit the dealer. The mazda dealer wanted $150 to diagnose the problem, and then doesn't want to even look at it after learning the Fortin system was installed. 

Connectez-vous pour répondre Voir 1 réponse(s)

15/05/2016

 Mazda Tu Tran2 (490Pts.)

1

2003 Mazda Tribute Evo One doesn't remote start without Key by the ignition

Hi, I'm installing an AX-One unit in a 2003 Mazda Tribute with revo-1 remotes. I'm using guide #16941, because I can't find CAN HIGH and LO. I got a1, a2,a3, a10,a11,a20, e2,e3,e4,e5,e6 connected. Programming and dcryptor went smooth. Got the revo-1 remotes programmed also. If I hold the key by the ignition the car will start. Without the key by the ingition the car won't start. I did noticed on Wirecolor.com a "Key sense" wire in the ignition harness. But I do not see where that connect to on the guide. Is that the wire I'm missing? Or is there something else? Thanks,
Connectez-vous pour répondre Voir 1 réponse(s)

19/01/2016

 Mazda Alexandre Pinard (130Pts.)

0

mazda 3 les portes debarre apres le demarrage avec loption 6 (lalarme ce declanche)

mazda 3 2012 les portes debarre apres le demarrage plutot que avant ( loption 6) donc l'alarme se declanche au demarrage puis quelques seconde plus tard les portes debarre et l'alarme cese que puis-je faire?
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer