English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

26/10/2024

 Honda StevenM (130Pts.)

0

OVE-ONE no LED lights when 6 pin main harness is inserted

EVO-ONE with HON2 Tharness and EVO Start module. Programming with Flash Link Updater was completed successfully but when connecting 6 pin main power harness inside the vehicle while holding down the programming button, none of the LED lights illuminate. Power harness leads were tested with a multimeter and there is 12 volts but the EVO-ONE LED's do not light up so I cannot enter the dcryptor programming mode. Even though none of the lights on the EVO-One illuminate, the connected EVO Start module has a flashing RED led so there is definitely power going to the EVO-ONE. Installed on a 2019 Honda Civic
Connectez-vous pour répondre Voir 1 réponse(s)

15/12/2018

 Volkswagen Clive Jacques (200Pts.)

0

RF642W No LED

I just installed an EVO-ONE in my 2016 VW Golf GTI Push-to-Start manual transmission using the T-Harness (THAR-VW1).  It was tedious, but it went well.  The EVO-ONE can remote start the vehicle using the OEM remote (3x lock).

Then, I added the RF642W kit.  Just plugged the black harness from the RF642W into the "data link antenna" port on the EVO-ONE.  I can't get the 642 to do anything.  I tried to program the remote transmitters but I cannot get the LED to come on.  I don't have a valet switch installed, so I'm using the ignition on/off method.  On-Off-On does not set the LED.  I've just setting the ignition "on" off 3 times and starting/stopping the vehicle 3 times (the instructions assume you have a key, not push-to-start).  Nothing.

What should I do?

Connectez-vous pour répondre Voir 1 réponse(s)

02/12/2017

 Nissan Alex Mello (160Pts.)

0

Evo one won't remote start

im reposting this question because my response was a little delayed. 

I have a evo one remote start syesten in my 2012 Nissan Xterra. I installed it with with the T-Harness, install guide 33161. I also have the Fortin RF642W RF Remote Kit With Two 4-Button, 2-Way remote installed.  The module programs to the car but the remote start does not work. the lock and unlock function works properly, the blue LED on the module will light up for both lock and unlock, but when I press the remote start nothing happens. No LEDs on the module light up, but the remote will flash green and beep. the red led under the yellow loop does not light up either. I also updated the module with the flash link updater,  and cut the yellow loop for the automatic transmission. Any help would be apriciated. thank you

Connectez-vous pour répondre Voir 1 réponse(s)

08/11/2017

 Nissan Alex Mello (160Pts.)

0

Evo One programs but won't remote start

I have a evo one remote start syesten in my 2012 Nissan Xterra. I installed it with with the T-Harness, install guide 33161. I also have the Fortin RF642W RF Remote Kit With Two 4-Button, 2-Way remote installed.  The module programs to the car but the remote start does not work. the lock and unlock function works properly, the blue LED on the module will light up for both lock and unlock, but when I press the remote start it seems that the module does not recive the signal. No LEDs on the module light up. I also updated the module with the flash link updater,  and cut the yellow loop for the automatic transmission. Any help would be apriciated. thank you

Connectez-vous pour répondre Voir 1 réponse(s)

07/08/2016

 Ford travis peterson (390Pts.)

0

2014 Ford escape (non-push button) programs but won't start with oem 3x lock

Everything seems to be programmed correclty. The wireing harness is connected underneigth the steering column in two places, and the cam high and low are hooked up. C1 & D1 are ON in flash link manager. I got red and blue lights flashing after programming with two oem keys. I read somewhere on the site that the lights tell a story. Keeping that in mind, I don't any lights when hitting lock or unlock. 3x lock just locks the car 3 times.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer