Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Ara Her

Joined on the:

Aug. 30, 2012

Score

770

Comment(s)

28

Voted question(s)

1

Voted answer(s)

2

Votes up

1

Votes down

2

Votes up received

3

Votes down received

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

1

Toyota Land Cruiser 2016

is it the same connection as 2008-2015? or there's changes

0

Renault Stand Alone

Hi, Its mentioned that Renault is supported for stand alone. No any information relative to this

RENAULT FluenceKey Card Megane IIIKey-Card Scenic IIIKey Card   Thank you

 

0

Mitsubishi Pajero 2014, Petrol AT

Well Ive tried to use Evo All for install a Pajero 2014 Petrol AT, the wire location is the same as Eclispe, galant http://fortin.ca/download/13931/evo-all_mitsubishi.rev-20140127.pdf Ive used Avital 4113 D2D, Can High and Can Low 6 and 14 are different colours than the manual above, ive tried to remote start with the key inside and works, but when im going to program the Evo All, the blue light remain on and when I turn the engine to ON START, the blue light tunr off but not flashing as suppost to be. Can Low and Can High are connected well. what could be the issue? is it possible that CAN LOW and CAN High are different location or pin? Ive tried to invert them also but no success. SN: 001A06514991 WITH EXTRA KEY will works , but I dont want to keep a key inside. Ive tried to use hardwiring for the module, and same issue Thanx

0

Tundra Shut down after a second after remote start

Sometimes after remote start the tundra 2015, the vehicle shutdown . what if wire the yellow wire from evo all to Ign1 and Ign2 ? I'm thinking that with ign 1 only maybe is not enough . I've select monitor oem and D2D options, any more option to enable ? Thanx

1

unlock and lock outputs stand alone

Well Ive connected the lock and unlock wires from evo all to the vehicle , green and white from evo all to violet and red from vehicle ( Infiniti qx56 2012) 12 v when rest and 0 v when pressing lock or unlock ) after that I gnd the external outputs from evo , light blink one time blue and nothing happened, so what support to do the evo? I've also test the lock and unlock wire from evo while I und the outputs but nothing happens . suggestions and advices are welcome

0

stand alone Nissan/Infiniti PTS no keyport

Hi, in order to activate lock and unlock from external output device , Do I need to connect the lock and unlock wires from the car or will be recognized from the evo all? Remote start works perfect on Stand alone , when I send negative pulse to the external input door look or unlock , the module blink blue but doors remains same . Remote start input works right, only lock and unlock not response. thanx

1

Security light stays ON after start the vehicle

Hi there, Security light on infinit QX56 2013 stays ON after starting the vehicle and while driving. Installation mode: Standalone without Tharness. Remote start works perfect, the only issue is the security light stays ON when vehicle starts with remote start or without. after vehicle turn OFF, the security light blink like suppost to be. IVe tried to reset the ECU but still same. Any suggestion? Thanx

0

Tundra 3x lock evo all

Is it possible to use the 3x lock start option with evo all and aftermarket remote start , to start the vehicle with the oem key? In case yes, which. options need to be enabled . thank you

0

Pajero Sport and Regular Pajero

Hi Robert, which wiring match with the Pajero Sport and Regular Pajero, could be (outlander)?. Is it possible Standalone feature? Thanx

0

Hyundai Accent 2014

Hi, Do I nned to coonect from remote start other wires ? in the install guide its only mentioned to connect while running wire. Install type 6, programm 3. I belive need to connect accesories, Ign , etc,, thanx

0

LEXUS 570 doesn't start.

LEXUS 570 doesn't start when I press the lock button 3 times. Only ignition turns on for one second or less. But when fuse "DOME 1" is absent vehicle does start successfully. What can we do in this case?

0

Nissan murano standalone with harness 2013

Hi there, at Nissan murano New guide its mentioned that lock and unlock wires are optional . what does it means? If I dnt connect them what features will not operate in the Evo all? External outputs for loco and unlock? Which options do you recommend to use after flashing the module ? Thanx

18/01/2015

Ford Ara Her (770Pts.)

0

Ford Raptor 2013 EVO ALL T harness

Hi, I've done the installation using the tharness with Evo all for raptor 2013. But my surprise when I've went to program the module I've inserted the key but nothing come up in the cluster, not detect the key. so I've put back again all as it was before and still can not read the key when it's inserted in the cylinder. the oem lock, unlock even remote start working from the original key , but can not do anything when the key is inserted . any suggestions? thanx

0

Evo One- Activation Input

Is there an activation input in the Evo One Module? or its only with the Evo All. Thanx

15/10/2014

GMC Ara Her (770Pts.)

0

SIERRA 2011 EVO-ALL THAR-GM2

Hi there, the car is not starting untill i put the key closer to the key celinder using stand alone EVO-ALL THAR-GM2 3X lock in the user manual its mentioned to connect only 20 pin (White),5 pin (White). But what about 6 PIN (RED)? No need to be connected? what im doing wrong ? also try using the TB-GM2 but not workig. but its not mandator Please advise

0

infiniti QX56 2014 STAND ALONE

DEAR ALL FOR SOME REASON THE MODULE NOT SENDING GRND PULSE TO PUSH TO START. WHEN REMOTE START THE VEHICLE MAKE CORRECT THE PROCESS BEVEN BRAKES LIGHT TURN ON, BUT NO REMOTE START IM USING standalone_evo-all_thar-nis1 WITH RECOMMENDED FIRMWARE. ANY SUG. THANX

0

OEM Remote Start

Hi there. for Infiniti QX56 2013 with OEM remote engine start. Do I need to desactivate the oem remote start in this vehicle in order to proceed with the evo all? Thank you

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue