Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

18/12/2018

 Nissan Justin Nail (130Pts.)

0

I've installed my evo-nist1 per install guide #74301 and no start.

3X lock and the evo goest through a cycle, parking lights illuminate, brake lights illuminate, but no start. The more I attempt to research the issue the more diagrams I see with different wiring diagrams. Evo also flashes red three times upon completion of cycle. I have exhausted all options I could come up with on my own to resolve the issue, to no avail. Please help! 2015 Nissan Sentra SV push to start
Login to reply View 1 answer(s)

30/11/2018

 Dodge David Davis (640Pts.)

0

2017 Dodge Journey Install Guide States I need a Resistor but I don't see where it's used?

I am reviewing the install guide #74201 and on the first page it states that the install requires 1 resistor. But it doesn't say what kind of resistor and the rest of the instructions never mention it. Also on page three the instructions show a wire location with the number 3 in which it states "passenger kick panel" but the image is showing the "driver kick panel" Can anyone clarify these install instructions.
Login to reply View 1 answer(s)

07/09/2016

 Ford Frank Ortega (180Pts.)

0

issues with programming it to a 2013 f150

When programming the unit as a stand alone remote starter "lights red and blue on" i run through all the steps for using both keys but i never get the lights to flash on the unit. They stay solid red and blue the entire time. Just to make sure i wanted to reset the evo-all but i cant figure out how to do that. I already have the data link and i flashed it to the recommended firmware 71.28. I basically want it just for the remote start. I wanted to use the alarm features but i am so lost with the instructions. My kit came with the T-harness.
Login to reply View 1 answer(s)

18/12/2015

 Ford KENNETH LLOYD (130Pts.)

0

EVO-For.T1 not programming. Are all wires needed?

Just received a EVO-FOR.T1 for a 2010 Ford Fusion (automatic, key start). Have installed remotes before. Saw a You-tube video that showed installation of the four plugs on the ignition module and only 2 additional ones for Can-High and Can-Low on teh ODB-II socket. The instructions via the Fortin site (Addendum-Suggested wiring harness configuration - Guide 32161 Ver 20150428 was difficult to follow. I then registered and downloaded the Wire Color instructions (Addendum-Suggested wiring harness configuration - Guide 32221 Ver 20150428) which showed 5 additional wired connections (including a hood contact pin that wasn't part of the kit) and a need to cut a loop for automatic transmission (which wasn't on my Fortin module. It seems the module in the instructions is a EVO-ONE whereas I was supplied with a EVO-ALL. So far, I followed the You-Tube showing the four connectors with the ignition module, and the Can-High and Can-Low. Although the You-Tube showed a successful programming cycle, mine did not turn on the ignition at the final step. Do I need additional wiring? Do you have any clearer installation material for the unit I purchased? If not, how do I learn what I need to complete this installation.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue