Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Cant program '15 Kia Optima PTS

I have everything wired on my '15 KIA Optima Push to Start. When i go to program i get to the step where i push the button 7 times. The red LED never flashes 10 times and the blue never comes on after. When I hard wired CAN1 CAN2 wires, the wire diagram shows it connected to a wire in a harness in the driver side kick plate. But there are 2 wires in each pin in the harness. (2 white/orange wires, 2 white wires). DO i have to splice to BOTH of the wires in each pin placement? Or will connected to only 1 work? This is the only thing i can thing of why i can not get mine to program.

0

2012 soul standard key no can bus communication evo one

2012 Kia Soul standard key no immobilizer. Using thar-one-khy1. Blue light won't flash when programming. I can read codes and voltage to the fortin module white 5 pin matches obd output at around 2.37v low can and 2.67v high. Module,flashlink all at the latest firmware. Evo one flashes successfully. Just when key on it fails to finish programming. Also wired in the fortin hood switch. Any help? Since it's such a simple install it's embarrassing to ask for help. Should work and great instructions as usual.

0

2012 soul standard key no can bus communication evo one

2012 Kia Soul standard key no immobilizer. Using thar-one-khy1. Blue light won't flash when programming. I can read codes and voltage to the fortin module white 5 pin matches obd output at around 2.37v low can and 2.67v high. Module,flashlink all at the latest firmware. Evo one flashes successfully. Just when key on it fails to finish programming. Also wired in the fortin hood switch. Any help? Since it's such a simple install it's embarrassing to ask for help. Should work and great instructions as usual.

0

EVO ALL CAN Bus confusion

Good evening, I am wiring up an EVO All with a Viper 4706V on a 2015 KIA Sorento. I am confused on the CAN1 and CAN 2 locations. According to guide 10841, CAN1 is located on the back of the fuse box, and CAN2 is located on the ODB-II connector. Yet, WIRECOLOR.com shows the opposite. And looking at the standard pinouts for ODB-II, it just shows can bus high and low on the ODB-II, no 1 or 2 spec. Anybody out there do one of these installs? Not sure which doc to trust here... Thanks, Jim

0

Can Wire Locations

I am working on installing an evo all as a stand alone alarm only on a 2011 kia soul pts by question is what are can 1 and 2? The fortin guide show can 1 at the obd plug and can 2 behind the cluster but wirecolor.com shows can 1 behind the cluster and can 2 at the obd! which one would be correct?

1

2015 sedona won't program evo-all

i installed autostart with evo-all i used D2D and program perfect but door lock,unlock is not working and not detected hood pin,door status,brake s/w i rechecked can bus high,can bus low wires one side 5v,other side approx 0v so tried connect opposite side,but won't program also tried the other brand bypass module(idata) but no change i working at kia so i look at ours manual. 100% correctly connected CAN high and,low lines what i need to check now?

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue