Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

27/08/2023

 Ford Thomas Daniel (200Pts.)

0

Programing evo-all in 2013 Escape

Trying to install an evo-all with the thor-for1 t harness into a 2013 escape with standardkey start. Just want the remote start feature. Evo module came from my sons infiniti g37x. It has been reflashed with flashlink to be installed in the escape. Concerning that the flask status bar never goes over 25% beofore it "comepletes" the flash. The module will not program to the car. With the standard 2 key programing, when I get to step 8 and press and hold the program button, the vehicel never starts and the bule and red leds come back on solid. If I try the Dcryptor medthod, with either key, the red led never goes out and yellow never comes one durring the key cycle steps. if I just plug the module in w/o holdong the program button, all the leds flask as if the module is not programed. As the thor-for1 did not come with a C plug, I took the ones from the infiniti harness. however I do not have a A plug either, but not sure that is needed...?
Login to reply View 1 answer(s)

21/05/2023

 Ford Pbellouny (130Pts.)

0

Use Evo-one in a vehicle with no transponders.

We have a 2014 E-250 it was ordered as a commercial build specifically without a transponder. I am interested in installing an Evo-One in it for remote start and security. Will it work without having the bypass programmed as it is not necessary. Would I need to install a different firmware on it?
Login to reply View 1 answer(s)

16/11/2022

 Ford manpreet singh2 (130Pts.)

0

2011 Ford Fusion Standard key, only blows cold air after remote starter installation

I installed evo one remote starter on the 2011 ford fusion s, i hard wired all the wires, did not used t harness, but after installation, i was getting only cold air from the vents with starting from remote, i can change the blower speed. couldnt change the vent modes and the air temp. if I start it with the key, heat blows only for couple minutes and it switch back to cold air it self, and has to restart the car to make it blow hot air for another couple minutes. any idea what could be wrong here,? any help will be appriciated,
Login to reply View 1 answer(s)

22/02/2022

 Ford Clay Smith2 (130Pts.)

0

removed this kit now car wont start with key

ok i am an installer at 12 volt solutions in tulsa oklahoma, and we installed one of your evo all kits in a 2016 ford escape, and couldnt get any power to the module so we removed the kit and plugged it all back up factory and now as soon as you turn the key to accessory it tried to start, and when you try to crank it over it does nothing. All the lights and the radio come on but wont start.
Login to reply View 1 answer(s)

04/01/2020

 Ford Chris carlton (130Pts.)

0

What yellow wire do i need to cut in the loop?

What yellow wire do I need to cut in the loop ?
Login to reply View 1 answer(s)

01/01/2020

 Ford Evan Netherton (160Pts.)

0

2013 Focus - What update do I need/How do I get pass the PATS system.

Car will light up and act like its on, but car wont start and the display will say No Key Detected, which makes sense, but how do I get it to not say that and start? Also what firmware version do I need for it? It's an EVO RS FORT1 system. Any info helps! thanks
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue