Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

03/10/2023

 Subaru THOMAS ZELMORE (130Pts.)

0

why do the factory keyfobs deprogram after installing evo one in a 2011 subaru imprezza with standard key?

I installed an evo-one (no t-harness) in a 2011 subaru imprezza, standard key. after programming and install, the factory remotes deprogrammed and would not work. I had to start the car on both keys to reprogram them. The same thing happened three days later.
Login to reply View 1 answer(s)

08/04/2023

 Subaru hofs1 (350Pts.)

0

2023 Forester w/key is Evo-One with T-Harness truly plug n play NO cutting splicing anything??

Last vehicle i did was 2011 Nissan Juke and even with T-Harnes etc I still had to splice a few wires etc. Is the 2023 Forester simpler ? I still see some type of cutting the imobilzer wire?? Will 3x oem key work?? My still having the flash tool should help keep cost down yes??
Login to reply View 1 answer(s)

11/12/2021

 Subaru Mark Bittinger (160Pts.)

0

Subaru Legacy will not remote start

I have a 2016 Subaruy Legacy Limited with key start. The EVO-1 with T-harness worked fine. After hitting a deer and vehicle being repaired(all body, no mechanical repairs), it does not remote start. Press lock button 3 times, the red light, then the blue light, then the yellow light comes on. Dash lights come on, parking lights come on, then all shut off. Parking lights flash 4 times, then reattempts starting, then same thing. I removed the unit and updated with flash-link, still does not work. I had read about valet mode adn pressing lock and unlock buttons to get it out of valet, nothing. I read about no tach signal, but there is not tach wire on Evo-1 I read. The unit is Service # 002B07 267043 I know I am overlooking something, I just cannot see what it is. THANK YOU!
Login to reply View 1 answer(s)

04/12/2021

 Subaru Gintaras Macijauskas (130Pts.)

0

Can't get into the car after remote-start

Hello, I purchased a second-hand Subaru WRX STi 2017 (manual, normal key) with Fortin Evo-one(?) installed and FTXDUO remote control. Remote start works ok (thank you for that - a great product!). The only problem is that after remote start I can not get into the car - buttons of original key do not work. If I press Unlock button on FTX, the car unlocks and then locks up immediately. I have to remote-stop the engine, only then I can use original key to unlock the door and get into the car. Something must be missing here, but what? Or am I doing something incorrectly?
Login to reply View 1 answer(s)

11/02/2020

 Subaru Ortega Armando (230Pts.)

0

Car wont start remotely

Finally got past step 5. Module is now programed but wont start with the remote, nor wil the doors unlock or the tailgate, if the doors are loked they will unlock. no lights on the module light up when attemptin a remote start. Double checked the wiring, all is good
Login to reply View 1 answer(s)

08/11/2019

 Subaru Nick Frank (160Pts.)

0

Yellow led stays on. Car won’t remote start.

09 Subaru Legacy with evo one, standard key and manual transmission. All of the wires are installed and I followed the procedure for the dcryptor programming successfully, however I haven't been able to remote start the car. When I try to do the procedure (foot on brake, pull hand brake, release foot brake after 1 second) that's where I get stuck, holding the start button for 3 seconds does nothing for me, the parking lights don't flash or do anything. All of the functions of the remote work fine I can lock and unlock the door I have no issues starting the car with the key or anything. The LED on the unit remains yellow no matter what I do t's my understanding it should be flashing blue when I press buttons. I have already changed over the settings with the flash loader for manual transmission but still no luck. can anyone help me figure this out.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue