Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

21/01/2023

 Ford Joseph Oyervides (230Pts.)

0

Key-Override-All, is the red light bulb on the module supposed to stay lit still even after programming is complete?

Remote start works perfectly fine even after red light remains on after programming
Login to reply View 2 answer(s)

21/01/2023

 Ford Joseph Oyervides (230Pts.)

0

Key-Override-All, is the red light bulb on the module supposed to stay lit still even after programming is complete?

Remote start works perfectly fine even after red light remains on after programming
Login to reply View 2 answer(s)

27/12/2021

 Ford ryk (220Pts.)

0

2011 Ford Escape red light stays on during programming - SOLVED

Vehicle: 2011 Ford Escape

Evo All #001A07260304 installed with T-harness THAR-FORD4; plug-n-play install, teed connections to ignition switch, immobilizer antenna and OBDII connector; no wires spliced

Can't get the unit to program.  Process: Hold program button, plug in data cable and release on red light.  Insert key and turn on until theft light turns out.  Remove first key and insert second.  Turn on for 3 seconds, theft light goes out, turn off and remove.  Last step says to press and release programming button within 5 seconds (this is where it gets stuck).  Red light should flash 10 times and blue light should flash 10 times and ignition comes on and turns off again.  When I press the button the last time, the red light blinks and just stays on.

I've tried the firmware downgrade listed in https://fortin.ca/en/qa/92073/faq-red-led-stuck-on .  That link says to downgrade to v 0.99 but the lowest version for Ford appears to be 4.01.  I flashed 4.01, power cycled in vehicle, reflashed v 71.52, unlocked settings and reset the unit.  Still same results.

I've also tried testing the data bus.  Hold button, insert data link connector, release button on blue light.  Connected all other connections and turned key on.  Blue light stays solid.  Shouldn't it flash on data?

The yellow wire is not connected as it seems to be part of the T harness, but I've tested it for 12v on ignition and it is getting it.  I don't have the valet switch or hood pin switch connected.  What am I missing?  I'm wearing out the plugs with all these connections/disconnections.

 

 

 

Login to reply View 1 answer(s)

19/12/2021

 Ford Chris Greer (130Pts.)

0

After programming - once red 6 pin is plugged in, red light on Evo all stays solid.

2014 Ford Explorer - Ford4 wire harness. Once I've completed programming and plug in the red 6 pin, dash lights and cabin fan comes on as though ignition is set to on (no key in ignition). Will not turn off until red 6 pin, hodd latch plunger or data cable is unplugged from Evo All unit. Something rattles inside of Evo unit which could be source of issue potentially?
Login to reply View 2 answer(s)

19/12/2021

 Ford Chris Greer (130Pts.)

0

After programming - once red 6 pin is plugged in, red light on Evo all stays solid.

2014 Ford Explorer - Ford4 wire harness. Once I've completed programming and plug in the red 6 pin, dash lights and cabin fan comes on as though ignition is set to on (no key in ignition). Will not turn off until red 6 pin, hodd latch plunger or data cable is unplugged from Evo All unit. Something rattles inside of Evo unit which could be source of issue potentially?
Login to reply View 2 answer(s)

18/12/2021

 Ford Corey Wilson (130Pts.)

0

Red light stays on during programming and wont program the keys

I hVE 2008 Ford Escape. I installed the Evo all fort4 with the the t-harness. I have installed all connectors(1,2,3) and connected a relay to the lights as instructed in step 4. I plugged the black connector in while holding the button in and then let it go when the red light came on. I put in each key for 3 seconds each and then pushed the button in. It didn't start the vehicle. Red light stayed on teh whole time. It only blinked when I pushed the button in. What causes this and how can I fix it?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue