Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

05/03/2019

 Ford chrisytsma (130Pts.)

0

2010 Ford Escape Hybrid Door Pin Wire Location

I FINALLY found the 26 pin plug where the Green/Violet Driver Door Pin wire is located. It's in the driver kick panel. But it is all but impossible to get to. Really really really difficult as it is buried behind steel braces that cannot be removed. There is certainly not enough slack to get fingers in there to cut the wire and then attach the 2 separate wires needed. How do I accomplish this?
Login to reply View 1 answer(s)

14/12/2018

 Ford JUSTIN CREMEANS (130Pts.)

0

2012 Ford Fusion Hybrid Compatibility

I've purchased an Evo about a year ago, installed everything and could never get it to work. It would set off the alarm instead of starting. Unfortunately, I had to return it. I would like to try again but I cannot get a clear answer. Is the system even compatible with a 2012 Ford Fusion Hybrid? There is no mention of the Hybrid on the site, just the standard. I would like to get a clear answer and purchase it again if I find out it should for sure work.
Login to reply View 3 answer(s)

01/01/2018

 Ford john collier (190Pts.)

0

Can EVO-ALL standalone be installed into a 2007 ford escape hybrid?

Guide 32171 (THAR-FOR1 THARNESS stand alone installation) indicates that the evo-all module can be installed into a ford escape hybrid vehicle. The evo-all module I have is programmed with C1, D1, D1.6, A5 off, program lock, and H2. It is not programmed with D4 though. Guide 34441 for stand alone installation shows that the D4 option is required for hybrid vehicle, which mine is). I have a T harness also with this module. Does the evo all module have to be programmed with option D4? Also, the lock/unlock input external controls are connected via a dashed line in guide 32171. Do these dashed lines indicate that they don't have to be connected as it is an option? Thanks for your help.
Login to reply View 1 answer(s)

17/01/2016

 Ford Jason R Allen (190Pts.)

0

installer says that Key-override-all is defective

I had a rs-160-edp+ v-2.0 installed by a local insaller and he is telling me that the key-overide-all is causing my 2009 ford escape hybrid to resart and that it is defective and I need to replace it . The vehicle wil lsart but it stops runing after about ten seconds and then restarts.
Login to reply View 1 answer(s)

17/01/2016

 Ford Jason R Allen (190Pts.)

0

tach wire for ford escape hybrid 2009 with ms sync

the wiring diagam shows pin 140 (ac/data)but on the ford escape hybrid 2009 with MS sync that wire is not there. what wire is the right wire for the tach?
Login to reply View 1 answer(s)

03/01/2015

 Ford Josh Smith (310Pts.)

0

Well is it normal for the evo not to turn on the ready to drive light on a fusion hybrid??

The dash lights up basically like with key in the ignition but the check engine light comes on and stays during the entire remote start sequence!! Never seems to go into full on?? During and I've already ran it through at least complete remote start cycles and still won't start engine!! Otherwise seems to be working fine!! The temperature here is around 40 degrees Fahrenheit today!! Again the ready to drive light doesn't come on at all during remote start!! This after 4 or 5 complete remote cycles!!
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue