Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

07/08/2020

 Other Matthew Currie (130Pts.)

0

Remote start status (eg. Wiper Interrupt) when GWR (Dark Blue A8) is configured for RAP pulse per Function 32 Mode 3?

Product: EVO-ONE Vehicle: 2010 Toyota Tacoma (Standard 40-bit Key) Configured per Fortin application note I am looking for a signal (negative or positive) to indicate that the EVO-ONE has remote started the vehicle and that it is currently running. Ultimately looking to slave features such as wiper inhibit, defrost, etc. I understand that the Dk. Blue A8 "GWR" configured as Function 32 - Mode 1 or Mode 2 would be exactly what I need however I am required to configure GWR as Mode 3 for "Autolight shutdown" per the installation guide for my vehicle. I haven't looked at the signal with a scope or logic analyzer to confirm but it sounds like it will pulse ground only at the end of the remote start run but otherwise float high impedance. I have scoured all documentation I can find but am wondering if there is another pin which may have an undocumented setting or alternative function which could be used for this? I suppose in this case, I could force GWR line back to Mode 1 and then program a microcontroller to then mimic the RAP signal needed for Autolight shutdown -- but -- hoping there is a trick I am missing.
Login to reply View 1 answer(s)

13/11/2019

 Subaru Mathieu Froment (130Pts.)

0

Status des portes erronés sur Outback 2018

J'ai remarqué que le status des portes est erronés sur mon application Evo Start 2. Lorsque que je demande le status de l'auto à partir de l'application, celle-çi m'indique que mes portes sont débarrés, mais les portes sont belle et bien barrés ?
Login to reply View 1 answer(s)

04/03/2018

 Acura Jesus Ocampo (180Pts.)

0

issues with door locks and overtake

So I've Installed a Viper remote starter on a 05 Acura RL this vehicle has a keyless smart key and also key to turn the ignititon switch... So I've programmed EVO-ALL using only the key unable to do so with the keyless, is there a way to program the keyless? Remote starter function works properly starts with no issues now problems im facing Acura alarm has to be disarm before starting, well once it starts doors dont lock as well no status input is present I can open the door press the brake even shift it into gear and it wont shut off... So remotes and door locks become inop when the vehicle starts and after I shut it off from the remote everything works again I've double check my connections and they all are on the right spot... EVO-ALL is communication with the vehicle when off but not when engine running... Hope im clear enought Any ideas or suggestions is highly appreciated possible im missing somthing but not sure?
Login to reply View 2 answer(s)

04/03/2018

 Acura Jesus Ocampo (180Pts.)

0

issues with door locks and overtake

So I've Installed a Viper remote starter on a 05 Acura RL this vehicle has a keyless smart key and also key to turn the ignititon switch... So I've programmed EVO-ALL using only the key unable to do so with the keyless, is there a way to program the keyless? Remote starter function works properly starts with no issues now problems im facing Acura alarm has to be disarm before starting, well once it starts doors dont lock as well no status input is present I can open the door press the brake even shift it into gear and it wont shut off... So remotes and door locks become inop when the vehicle starts and after I shut it off from the remote everything works again I've double check my connections and they all are on the right spot... EVO-ALL is communication with the vehicle when off but not when engine running... Hope im clear enought Any ideas or suggestions is highly appreciated possible im missing somthing but not sure?
Login to reply View 2 answer(s)

03/01/2017

 Ram Ronald Berry (130Pts.)

0

EVO-All and Directed Smart Start - No Status

Installed Directed Smart Start with my EVO-All Stand-Alone. When using the Smart Start App, it does not give engine status when click on remote start, so I have no way of knowing if start was successful if away from the vehicle. It gives me status when I lock or open doors. Any suggestions on how to fix this?
Login to reply View 1 answer(s)

12/03/2015

 Chevrolet Hank Rath (310Pts.)

0

OEM car alarm is armed after shutdown of engine

I know that the EVO-ALL is not supposed to be enabling a push-start button system - but i does a real good job despite. After having unsuccessfully tried the EasyGo and EasyCar systems, finally the AdvancedKey system (the new AK-105B version) works great on my 2012 Camaro with your EVO-ALL providing most of the connections! While the features work fine, including remote start and push2start button, I do haven one quirk that I hope to possibly be fixed by maybe changing a certain setting of the EVO module... When shuting down the engine, the OEM alarm is armed. With the remote start, this makes sense - but when shutting the car down from RUN mode to OFF obviously, that is bad - forcing the driver to exit right away or use the OEM remote to disarm the OEM alarm. Is there an option to prevent the triggering of the OEM Alarm on GWR termination somehow option-wise? Thanks HR
Login to reply View 1 answer(s)

20/01/2015

 Kia LaCorey Will (420Pts.)

0

EVO-ONE/SmartStart statuses...

Is there any option in the EVO-ONE menu items that will enable the SmartStart to provide the statuses in the SmartStart app (doors: locked/unlocked, ignition, trunk, etc.)? Plans to get this to work? Currently, I get the error message in the SmartStart app that it's unable to interpret the info from the server. NOt sure if it's something with the EVO-ONE or something associated with Viper/Directed.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue