Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

17/11/2024

 Dodge jay12345 (130Pts.)

0

2005 Dakota No Remote Start

EVO-CHRT5 RS with T-harness. Using as stand-alone remote start with oem remote. A1 connected to Ign 1 & A15 connected to grounded hood switch. When inserting 20 pin connector blue light goes out, comes back on when key is turned on to continue programming balance of programming seems OK. After remote is programmed yellow light stays lit. Do get blue light & horn honk on remote activation but no attempt to start.
Login to reply View 1 answer(s)

19/11/2022

 Ford Christian Smith (130Pts.)

0

Why do all three lights flash when I put on the 4 pin connector CHRT5?

ASIN B00BMWS5HK

Login to reply View 1 answer(s)

01/01/2022

 Jeep Dave Casselman (130Pts.)

0

What connection did I miss? 2009 Jeep Compass

2009 Jeep Compass automatic. Kit is EVO-CHRT5 with a built in T-Harness and a EVO-ALL Install is complete and programming procedure completes correctly at each step. No extra sensors- no hood switch or valet switch yet. But there is no start with the remote. Vehicle starts normally with the key in the ignition. I received a code in the box for wiring color setup and had to choose from about 8 guides. The displayed numbers mean nothing as the numbers at the top of the pages when printed show something different. I am using Guide 63651. Besides the T-connections, I also connected the two yellow wires together. No other wires were connected and I am not sure what to do with the purple wire #18 as the drawing says it goes to the kick panel at item 3. What is it wired to? A troubleshooting guide says to check for power at yellow/red and yellow/blue. I get nothing when trying to start. New: I found a comment on a youtube video about hooking the green/red wire to the purple wire in the T-harness. That does not make any difference for me. Still no attempt by the car to turn on or to crank. Of course the horn honks and the doors lock each time I hit the lock button.
Login to reply View 1 answer(s)

12/12/2021

 Jeep Chris Schiszler (130Pts.)

0

2005 Jeep Grand Cherokee brake wire relay

What relay do I use to wire directly to my brake? My evo all is not shutting down when the brake is pressed and tech support said I need to wire directly to the brake with a relay to reverse polarity. Thank you.
Login to reply View 1 answer(s)

13/02/2020

 FAQ Jason Field (130Pts.)

0

Wires on Excalibur echo 5, 2 way rf extender kit

I see the install where you take off the data plug from harness and put in the green,blue,red,black wire from echo 5 antenna but there are three more wires. The gray is for valet switch so I don't need to hook that up but the are another blue,green wire that's say led where do I hook them up to or I don't have too? Using evo-all standalone setup with chrt-5 wiring harness. Do i just join the other blue and green wires with the other blue and green, then the led lights on the antenna will work right?
Login to reply View 1 answer(s)

03/11/2019

 Jeep Levi Kudrna (240Pts.)

0

What firmware for 2015 Jeep Cherokee?

I have an EVO-ALL with T-harness for a 2015 Jeep Cherokee. I'm having problems programming it to the vehicle. The lights on the unit aren't flashing per the instructions. I have firmware 68.01 as this was recommended in FlashLink. While troubleshooting, I noticed the website said minimum firmware is 74.24. Should I flash it to the latest 74.xx firmware instead?
Login to reply View 2 answer(s)

03/11/2019

 Jeep Levi Kudrna (240Pts.)

0

What firmware for 2015 Jeep Cherokee?

I have an EVO-ALL with T-harness for a 2015 Jeep Cherokee. I'm having problems programming it to the vehicle. The lights on the unit aren't flashing per the instructions. I have firmware 68.01 as this was recommended in FlashLink. While troubleshooting, I noticed the website said minimum firmware is 74.24. Should I flash it to the latest 74.xx firmware instead?
Login to reply View 2 answer(s)

12/01/2019

 Jeep Rylee Stevens (230Pts.)

0

2005 jeep grand Cherokee wiring problem

I made the extra connections as per 28831 - F I have an evo all with hardware 6 and newest firmware. I also have the 642 remotes. Everything works except starting the vehicle. The evo bypasses the built in immobilizer and the LEDs flash like it's trying to start.
Login to reply View 1 answer(s)

01/01/2017

 Dodge Clarence Leavitt (340Pts.)

0

What is wire A13(Yellow/Blk) - External Input for?

Is the A13 wire required in stand alone evo all
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue