Utilisateur

2010 Subaru Impreza, Compustar CM7000 alarm and remote start, EVO-ALL in data mode. Each time I use the Compustar remotes the vehicle locks/arms then immediately unlocks the doors leaving alarm on. Tried different CM7000 and EVO-All. Both of the Compustar remotes acting same way. The vehicle locks and unlocks doors,flashes lights and beeps OE beeper multiple times with each press. Ser#001a07-250179. Guide #57421

2019 Elantra GT manual with EVO ALL, Compustar CMX. Vehicle starts properly, but after a remote start sequence the signal, headlamps and a few other accessories related to steering wheel mounted controls do not work. Only way to regain operation of these functions in to remove cars battery for a few minutes. Happens only after 5-8 remote start sequences. Removed parking light control from EVO and hard wired directly to Compustar with appropriate resistor with no change.

2019 Veloster, PTS, using EVO-ALL and Compustar CMX. Parking lights stay on intermittently after locking the vehicle. Is there somewhere else I can hook up positive lights to instead? Tried different module and remote starter.

Loking to do a 2014 VW Golf Diesel. Is this doable using a EVO-ALL and TB-VW?

2015 Toyota Sienna, key start. During programming, at step 5 the red LED flashes slowly four times. rechecked wiring, swapped module, reset, reflash. Even different brand of bypass. Any ideas?

Can an Evo-One and Evo-Start combination be used even if the vehicle does not have a transponder/CAN support? Vehicle is a 2005 Hyundai Satna Fe. All connections will be hardwired and vehicle does not have a transponder. Is the Evo-All an analoge starter out of the box ready for this sort of application?

Installed Compustar CM7000 with EVO-ALL. All works good. Customer states the hetaed seats do not turn off with key takeover. Is there any way to accomplish this? Controls are on the doors, so manually turning off the passenger side from the driver's seat is difficult.

Vehicle: 2015 Jeep Wrangler  Alarm: (New-Install) Compustar cm7000as w/2W704r-sh long range 2-way RF transmitter  Bypass Module: Fortin EVO-ALL    The only wiring done outside the CAN-BUS are parking lights, siren, hatch trigger and 12v switched connections.    - Doors triggers are connected through CAN-BUS; hood and hatch triggers are hard-wired into Jeep.  - Compustar DAS Tilt/2-stage shock Sensor is currently DISCONNECTED from the brain.  - DEI Proximity Sensor is currently DISCONNECTED from the brain.    About 20% of the time my Compustar will go into full alarm within 5 seconds of arming the system. I thought the issue might have been the proximity sensor so I disconnected it completely. When that didn't work, I also disconnected the DAS tilt/shock sensor with no change (currently no external sensors are connected).    After going into full alarm, pressing disarm turns off the siren but the parking lights continue to cycle through the full timeout period of 30 secs and the doors do not unlock. If I hit disarm a second time, the trigger cycle stops and the doors unlock but there are NO zone breaches indicated on the 2-way remote, by parking light or LED flashes as if the alarm never went off.    When the alarm triggers, I can disarm the system twice, stopping the cycle, and immediately ARM the system with no repeated full trigger.    Next, I disabled all triggers and unused options within the EVO-ALL with no change.  I finally disconnected the data wire from the EVO-ALL and I had not had a false alarm for one day.  I then reconnected the DAS Tilt/2-stage shock sensor and the DEI 508D Proximity sensor and haven't had any false alarms in two days.  This leaves me thinking the problem is either the EVO-ALL or there is something in the CAN-BUS that the EVO-ALL is picking up and causing the false alarms.  I'm hoping someone out there has a suggestion for me.     Thanks in advance for any help you can provide!