Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

Aaron Mcmullin

À rejoins en date due:

Oct. 22, 2010

Points

190

Commentaire(s)

3

Questions votée(s)

0

Réponses votée(s)

0

Votes positifs

0

Votes contre

0

Votes reçus

0

Votes négatifs reçus

0

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

0

2014 civic pts std with evo one with thar-hon3 will not enter reservation mode

Just installed a evo-one ( bybass firmware73.32 and .31 ) with hon3 t harness in a 2014 honda civic pts standard transmission, with all required settings enabled.( C1,D6,D2 and 2-2 and 38-2 ) I had set manual transmission ready mode for 33.2 and 33.1 after i programmed a rf kit . Unit programmed as it should, but the vehicle will not shut down after exiting the vehicle to complete ready mode. Also, the oem remote will not lock or unlock the car in this state. I had set the remote start sequence for lock 3x and also programmed a rf411 kit and same result, with the car not shutting off after exiting to complete reservation mode. Any ideas?

0

2018 qashqai manual transmission support reg key

On the website it lists the 18 Qashqai manual transmission as supported with the evo one, but in wire color it is noted that the vehicle is not supported. The 2019 also lists as "automatic only " So is the quashqai regular key with manual transmission actually supported? Thanks

0

04 Astro Van door locks not functioning properly with evo all and compustar

I have a customer with a 2004 Chev Astro van that I had installed a Compustar CM800s and Evo-All in and the keyless when used with the compustar remotes do not operate correctly. The unit will not unlock the passengers door completly,( unlocks half way or acts like it is stuck ) but operates normally with factory remotes and with relays installed. Everything else operates as it should.Firmware version on evo all is 4.06 and have tried various evo-all units.Units were flashed with both hardware versions of flashlink updaters. Compustar is also flashed to current revision.Evo- all was set in fortin and ads bypass mode in options menu. The only method I did not try is hard wire method.I also regrounded the unit twice to eliminate possible ground issues. Any ideas on a possible solution to this? Thanks I have since hardwired the keyless with relays and the problem is resolved.

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer