English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

13/12/2019

 Nissan Justin Naylor (130Pts.)

0

08 Nissan Pathfinder - RF642W Lock Button Locks, Unlock Button Locks, Programming Settings or Wrong Wire?

2008 Nissan Pathfinder S - Standard Key - OEM Alarm Fortin EVO-ONE With NIS2 Harness Guide Followed: 75611 Unit was flashed to recommended/newest firmware prior to install. Service No: 002B07 200206 Everything is installed and working (As far as the Remote Starter Goes). When using the OEM Remotes the vehicle will lock and unlock as it always has. However, when using the RF642W remotes, The remote start works flawlessly (Push button, parking lights on, start/Crank, Run) The lock button locks the doors, but the unlock button also locks them (and does not unlock). The OEM Remote will unlock the door as normal with the remote starter running, but I would really like to not have to carry two remotes with me. Vehicle Running Oem Remote: Only Solid Yellow is on, No Blue Flashes RF642W: Lock - Solid Yellow, Blue Flash - Locks Doors RF642W: Unlock - Solid Yellow, Blue Flash - Locks Doors Did I miss a step? Enable/disable a wrong option? Any help is greatly appreciated. Thank You in advance.
Connectez-vous pour répondre Voir 1 réponse(s)

16/02/2018

 Nissan Keith St.jean (160Pts.)

0

2008 Altima PTS

Install evo-all and all wiring complete. After remote starting with oem key 3x lock, car runs about 3 seconds and shuts off. Then it tries to restart itself, ultimately leaving the ignition in the acc position. I Was told to flash a different firmware version of 72.23, still not working. Added rf kit revostart 1.1 same results. Need help please.
Connectez-vous pour répondre Voir 1 réponse(s)

09/12/2017

 Nissan Mark Whitman (240Pts.)

0

Doors locking after ignition shut off - Not programmed to.

2008 Nissan Titan, EVO-ONE with T-Harness install using RF642W remotes. Doors immediately lock upon turng engine off. What function am I missing to disable this? Tried Rico's advice. Alarm doesn't turn off if set off with RF642W remotes. May just diconnect and purchase a different remote start at this point. I'm really getting dissapointed with this installation. Neither contributors really answered the question. Update: Customer has asked to have remote start removed and replaced with a different manufacturer. Can't say I blame him.
Connectez-vous pour répondre Voir 1 réponse(s)

09/02/2015

 Nissan Jim (850Pts.)

2

Using Evo-All as a Stand alone on a 2007-2008 Altima

I am installing an Evo-All into a 2008 Altima and using the OEM remote as the first choice for the install. I understand from previous Q&A posts that the Evo-All can be used as a stand alone remote start in this model year but because it cannot detect the lock/unlock on the CAN BUS it will need to use a separate RF Kit or an Universal Trigger connected to the external input of the Evo-All. Also The Evo-All needs to detect the unlock pulse to allow key take over. A suggestion was to see if pin 15 on the BCM tests negative with a press of the unlock of the factory remote to connect the unlock input of the Evo-All to that. (Assuming that this pulses not only with the remote but also with a press of the door button) For the questions. If pin 37 on the BCM pulses negative with each remote lock press, could you just connect the Evo-All lock in wire to that pin to allow 3x remote start? One of the optional connections is to have the Evo-All lock out connected to pin 37 on the BCM and the unlock out to pin 15 on the BCM. Is it okay to have the Evo-All lock in and lock out connected to pin 37 and the unlock in and unlock out to pin 15 without causing problems.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer