English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

11/10/2020

 Ford Jaeden Hudson (340Pts.)

1

Fort2 programming issues

Trying to program my 17 f150 std key w/ keyless. I get to the point where it has me press the button 8 times. After I do that I put the key up to the ignition cylinder (not in it) and when I press the button, nothing happens. The red/blue lights stay on solid and the truck does nothing. I programmed the module with the latest firmware and other firmwares with no success. All connections have been verified. EDIT: Found out I had a bad connection however I have a new problem. After going through the programming sequence for the second key, after the ignition shuts off, the red LED flashes. When going back to the computer I get a message saying the immobilizer data received from the module is incomplete. I have tried the entire procedure 3 times with the same result. EDIT 2: I got it to go through all the steps. New issue now. When attempting to start the truck via the RF kit, I get a red light, then red/yellow light. They go out. Then I get red then red/yellow again. After that I get 3 red flashes and nothing else happens. The starter does not respond to 3x lock, although I can not remember if I disabled it or not.
Connectez-vous pour répondre Voir 2 réponse(s)

11/10/2020

 Ford Jaeden Hudson (340Pts.)

1

Fort2 programming issues

Trying to program my 17 f150 std key w/ keyless. I get to the point where it has me press the button 8 times. After I do that I put the key up to the ignition cylinder (not in it) and when I press the button, nothing happens. The red/blue lights stay on solid and the truck does nothing. I programmed the module with the latest firmware and other firmwares with no success. All connections have been verified. EDIT: Found out I had a bad connection however I have a new problem. After going through the programming sequence for the second key, after the ignition shuts off, the red LED flashes. When going back to the computer I get a message saying the immobilizer data received from the module is incomplete. I have tried the entire procedure 3 times with the same result. EDIT 2: I got it to go through all the steps. New issue now. When attempting to start the truck via the RF kit, I get a red light, then red/yellow light. They go out. Then I get red then red/yellow again. After that I get 3 red flashes and nothing else happens. The starter does not respond to 3x lock, although I can not remember if I disabled it or not.
Connectez-vous pour répondre Voir 2 réponse(s)

17/09/2018

 Nissan Stephen Puckett (160Pts.)

0

EVO ALL ONE programming issues

During programming of the EVO ALL in ONE the yellow light flashes and when I install the key to get the red and yellow solid light the blue light also comes on immediately solid and never goes out. So all leds stay lit solid at this point and I can go any further.
Connectez-vous pour répondre Voir 1 réponse(s)

06/05/2018

 Ram wizzled (130Pts.)

0

not programming?

I'm trying to program my EVO-ALL for my 2016 Dodge Ram with the tip start key. After pressing the programming 4x and the light turns to solid yellow it says "insert key" and the light should turn to red.  I insert the key and nothing happens.  I've flashed the module to 74.37 and still nothing.  I have master reset it and also programmed the can-bus  and the blue light stays solid on canbis programming. Any ideas?

Connectez-vous pour répondre Voir 1 réponse(s)

10/03/2018

 Hyundai Franck Ah-Kane (300Pts.)

0

Evo One Can Bus Data programming not flashing blue?

Hi all, I have installed the evo one inside my Sonata Limited 2016 PTS and went through the procedure outlined in the following page: http://fortin.ca/en/vehicles/hyundai/sonata/2018-push-to-start/troubleshooting.html Step 1: The module does not program correcty. Step 2: Step 5-6. Step 3: Blue led does not flash properly. Essentially, in step 5, when I start the ignition to on, the red LED flashes 10 times. Up to this point, everything is fine. Subsequently, instead of the blue LED flashing, I get both red and blue LED lighting up and remain as is. It only turns off when I turn off the ignition. I double checked my wiring but it does not seem to be the case. Would you have any suggestion? Best regards, Franck
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer