English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

19/10/2019

 Infiniti BLourenco (130Pts.)

0

'12 G37 - Is my EVO-ALL broken?

[EVO-ALL install on 2012 Infiniti G37 w/ THarness; SN/001A07 008704; Guide #80851] Issue: Cannot program the EVO-ALL. I get stuck on step 2. When I press the button twice, the yellow LED doesn't start blinking. In addition: 1) I noticed if I remove the data link cable from the EVO-ALL while the white 20-pin connector is installed, the locks contantly go off (always locking). I have gone over the wiring many times and am confident it's correct. 2) During step 1, I have to disconnect and reconnect the data link cable several times before it finally begins cycling through the LEDs. Is this normal? or is it asign of bad wiring? bad unit?
Connectez-vous pour répondre Voir 1 réponse(s)

10/02/2019

 Infiniti Nick Larsen (160Pts.)

0

2009 G37 EVO ALL NOT WORKING AFTER FLASH

1) I Installed EVO All and Tharness (programmed EVO while hooked up to harness in car > Evo lit up blue when pushing lock but car would not start using oem remote. (Learned I needed flashlink) 2) Bought flashlink 4 and updated and flashed EVO All 3) Reinstalled EVO All and ZERO lghts came on and car did not start I followed recommended settings: A1-11 ALL ON B2 OFF C1 & D1 ON D2 ON After flashing the EVO I depressed the program button and no lights come on. I plugged it back into the wiring harness and again, no lights. Before I flashed it the red light would come on while depressing the button...what could have happened? FRUSTRATED!!!
Connectez-vous pour répondre Voir 0 réponse(s)

05/02/2019

 Infiniti Nick Larsen (160Pts.)

0

2009 Infinity G37 OEM remote No Start

I just finished installing the EVO-NIST1 (no other components) on my 2009 Infinity G37. After hooking up the wiring harness I completed the bypass programming procedure and everything went good until I tried to start the car using my OEM remote. I pushed my OEM remote 3 times and the car did not start. Each time I pushed the lock button a blue LED light flashes on the EVO unit but nothing else happens. Do I need to order a stand alone remote? Do I need additional components? Not sure what to do here.
Connectez-vous pour répondre Voir 1 réponse(s)

01/02/2016

 Infiniti Frankie Aladi (160Pts.)

0

2011 Infinity QX56 Programing EVO-ALL & THAR-NIS1 Stand Alone

Car 2011 QX56 EVO-ALL & THAR-NIS1 Stand Alone Service # 001 A06 585175 Guide #12681 During programing when I get to #7 The red sometimes turns off and only blue is on. I have only been able to get both red and blue to stay on twice very briefly. In the instances when they stayed on, following the next step #8, Pressing the start and stop button x2 does not turn on the ignition. If you press it a third time or jump to #9 the the inginition turns on and it flashes rapidly. If I go continue with the programing, the result is that the car does not remote start on pressing 3 times. Basically nothing happens, it simply locks the door 3 times. I have an updated firmware. Did the update all over again yesterday successfully. I have been on this thing for the past 2 days. Have not done anything else all weekend. I am at my wits end with this thing. Somebody help.
Connectez-vous pour répondre Voir 2 réponse(s)

01/02/2016

 Infiniti Frankie Aladi (160Pts.)

0

2011 Infinity QX56 Programing EVO-ALL & THAR-NIS1 Stand Alone

Car 2011 QX56 EVO-ALL & THAR-NIS1 Stand Alone Service # 001 A06 585175 Guide #12681 During programing when I get to #7 The red sometimes turns off and only blue is on. I have only been able to get both red and blue to stay on twice very briefly. In the instances when they stayed on, following the next step #8, Pressing the start and stop button x2 does not turn on the ignition. If you press it a third time or jump to #9 the the inginition turns on and it flashes rapidly. If I go continue with the programing, the result is that the car does not remote start on pressing 3 times. Basically nothing happens, it simply locks the door 3 times. I have an updated firmware. Did the update all over again yesterday successfully. I have been on this thing for the past 2 days. Have not done anything else all weekend. I am at my wits end with this thing. Somebody help.
Connectez-vous pour répondre Voir 2 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer