English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

08/12/2019

 Ford Vít Švanda (140Pts.)

0

Ford Mondeo 2016 (push to start) - not started - 3 led flashes

Hi I have EVO-ALL (sn: 001A07051925) with firmware 4.01 and T-harness (EVO-FORT3).   I have connected 4-pin and 5-pin cable only. I use OEM remote.   The programming was successful (I think). Blue led was solid -> after push to start -> blue start to blinking rapidly (not only 10x, but blinking until turn off).   When I used LOCK 3x, then unit start blinking two times (red->orange->blue). After this two attempts blink red 3 times.   My configuration: A1, A3, A4, A7, A8, A9, A10, A11, C1, D1, D1.3, D1.6, D1.10, D6     Please help me.  

 

Connectez-vous pour répondre Voir 1 réponse(s)

04/08/2015

 Ford Sergey G (160Pts.)

0

Ford Mondeo Europe

All 4 CAN-bus connections were checked. The unit was master reseted. The unit being installed with a separate remote starter - security system (local brand) which has ground out for immobilizer bypass. And this out being connected to Fortin A8 connector. Security system has brake pedal and push-to-start button connections which start the vehicle as a regular start. And it's working great when the original key is inside the car. So, I need to bypass the immobilizer to have remote start. All other Fortin connections are the same as in the guide #14751 except parking light switch which is not needed for me as all external indications are going from the security system. During programming, when the ignition is ON (step 4) I have the blue light flashes 2x times, then the red light flashes 4x times then all together (door locks opens, head lights (low beam) and internal lights flashes one time) and after all of that the blue light flashes rapidly. The unit is not programmed. I also tried to program it with security system fully disconnected. The scenario is the same.
Connectez-vous pour répondre Voir 1 réponse(s)

03/08/2015

 Ford Sergey G (160Pts.)

0

Ford Mondeo Europe

Ford Mondeo 2015 Push-to-Start (Europe).

All wiring colors are the same as in the guide.

FORTIN connected as a Key bypass only (+12, GND, IGN, CAN1, CAN2, GWR to control).

Firmware 71.28

Hardware v.6

During programming I have five red flashes instead of ten and unit is not programmed.

Please advise. Thanks.

Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer