English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

06/02/2019

 Jeep Jeep Guy (160Pts.)

0

Viper smartstart not communicating with EVO ALL

I've installed a VSM350 in my 2008 Grand Cherokee, following the instructions (splice grey wire with black, plug in connector). The VSM350 has been activated by a local dealer and my viper online account is properly set up. I can update GPS information via the smartstart app (this confirms unit is powered up and communicating with the internet properly). I am not able to lock, unlock, or remote start using the app. When I attempt to lock/unlock or start, I receive the message "unlock failed at [time]" I have enabled H4 via flashlink. I live in a major city and the vehicle is parked outside, the issue is not related to cellular coverage; the app reflects that the vsm350 has 4 or 5 bars of signal strength. I appreciate any suggestions to enable the smartstart to communicate with the evo-all to enable the lock/unlock/remote start. Thank you
Connectez-vous pour répondre Voir 1 réponse(s)

01/02/2019

 Jeep Jeep Guy (160Pts.)

0

Programming EVO-ALL / CHRT4 with SmartStart VSM350

About a month ago, I successfully programmed and installed an EVO ALL with CHRT4 in a 2008 grand cherokee. The 3x lock would successfully initiate a remote start. I recently removed the EVO ALL to reprogram it with flasklink to enable H4 (smartstart). Upon reinstalling EVO ALL, I no longer had blue lights. I reprogrammed to the key and got the blue light to illuminate when clicking lock button. I connected the yellow to the yellow for ignition during initial install and that is still the case now. This yellow wire splice is the only wiring i've done outside of installing the CHRT4 harness. The current issue is that after reinstalling the EVO ALL, I do not get a red light on the EVO ALL after clicking 3x lock. The 3x lock is still enabled in flashlink, in addition to H4 being enabled. EVO ALL was already (and still is) flashed to the latest / best / recommended firmware. Given my inability to remote start with 3x lock before even connecting the smart start, i have left the smart start unplugged until i can resolve the failure to start with 3x lock using the key. I have tried re-flashing the evo-all with latest firmware in flashlink and starting over but am in the same position where i get blue lights but no red, and thus, no remote start using 3x lock. When vehicle is started via the key in ignition, EVO ALL gets a solid a yellow to indicate the evo-all knows it has ignition. My question is: What I'm doing wrong or do I not have connected properly to get my red light back after 3x lock so that the vehicle can start. Does H4 prevent use of 3x lock remote start?
Connectez-vous pour répondre Voir 1 réponse(s)

23/11/2015

 Jeep Ed Bradshaw (130Pts.)

0

CHRT4 installation with Parking Lights

In the installation instruction it notes:

If a parking lights (+) wire is use : they require more than

10Amp. Connect the remote-starter’s power directly to the

vehicles battery with the appropriate fuse.

 

Does this apply to connecting the (-) Parking Lights from plug A, on a Stand Alone installation?

Connectez-vous pour répondre Voir 1 réponse(s)

12/01/2015

 Jeep JEREMIAH PIERCE (160Pts.)

0

2008 Grand Cherokee Evo-All Stand alone will program but wont start

I installed the chrt4 stand alone unit on a 2008 grand Cherokee. It will program but will not start the vehicle. I tested to see if the yellow/blue wire had constant voltage(12V) and if the yellow/blue wire had voltage(12V) when attempting to start and it did. Im just at a loss for why it wont start. Any help would be appreciated. I bought this from the fortin website and supposedly it is updated with the latest software. thank you
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer