Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2015 Silverado work truck with no fobs. Can i add a remote start with fortin remotes?

0

2015 Silverado work truck with no fobs. Can i add a remote start with fortin remotes?

0

How to unlock vehicle after remote starting

2019 Chevy Cruze after remote starting keyfob doesn't work so how do you unlock vehicle? No keyhole in door

0

2014 Tahoe EVO-ALL no crank

Have the EVO-ALL installed with T-Harness in a 2014 Tahoe. After car is shut off with the key and remote start is attempted vehicle will start as it should. Any other time you attempt to remote start the vehicle it will go through the motions and power on ignition but will not crank. it makes two attempts and then shuts down with the 3 light flash. the ignition powers on and then goes out as if it was going to attempt to start but it does nothing. if i restart the vehicle with the key, turn it off and attempt again it will rempote start one time

0

13 Silverado remote start

Istalling a evo all stand alone on a 13 Silverado 3500 with stardard key with OEM Remote starter, program evo ok dash light will come on but no crank or start. Instal with Thar-GM4.

0

Evo all doesnt give me the option to use my oem fob in the flashing process

Why is there no option for oem fob on an 09 suburban but that option I'd available on other chevy models?

0

2020 Equinox OEM key not starting vehicle

So after decryption I connected the module, put the battery back in the key and did lock x3 with no crank. Lights, horn everything works fine. I can start the vehicle with the push-to-start while in the vehicle but that defeats the purpose of remote start. Also the blue light on the module flashes with lock and unlock, I've used the yellow and black wire to start but touching ground and it starts then. Any suggestions?

0

chevrolet aveo standard remote disabled after remote starting, starts anyway at the 5th lock not the 3th lock

i have the evo all installed with the GM1 t-harness, and i use my factory chevrolet flip key (aveo 2012 euro/sonic) the car starts at the 5th time pressing the lock button, not the 3th time, and if i try the option lock-unlock-lock then it don`t work.. if i remote start the car then de oem flip key is disabled and get no response from the car, i can unlock the car with the key, and if i push the unlock button in the car and press the brake it turns off and starts normally (automatic) license: (JV-198-N) Netherlands.

0

'13 Cruze, key-to-start, Evo Rs gmt1 installed, used dcryptor, and i went by all the steps, so why doesnt it still work?

0

OEM 3x Lock not starting 2007 Silverado Classic (now at flash limit)

I'm doing a first time install of the EVO-ONE (SN 002B048051) on my 2007 Chevrolet Silverado Classic 2500 HD Diesel and I followed Guide 61101 Rev 20190723 which stated the bypass FW must be a minimum version of 70.26. The latest version of my flashlink software wants me to use 70.18 (highlighted in green) which did not work so I then upgraded to the latest version 70.39. I found at the latest version the module would not recognize the key programming procedure (all led's flashed at same time when powered on). I then tried going down one FW version at the time (from the latest) and found that 70.34 is the latest version that will work as per the guide and accept key programming without all LED's flashing when plugged in. I'm now stuck at that version and cannot set bypass options any longer since my flash limit has been reached (not sure if not being able to set bypass options is due to flash limit reached or the fact I'm now at 70.34 because I know 70.26 did allow me to set bypass options). Both 70.34 and 70.26 are greater than the guide requires My remote start FW is 1.24 and I had enabled both options 38.2 and C1 along with other options for Diesel etc. According to the guide the 3x lock , heated seats etc should work on the classic and this module but I have yet to see success. When I start the truck with the key I see the yellow light come on showing the key is programmed however I do not see the blue light blink when pressing lock on my OEM remotes. I do have the Fortin Rf642 rf kit on the way and will setup the module to use those however I wanted to enable the 3x lock on the OEM remotes in the meantime. Can anyone point me in the right direction? what FW should I be running and can my module be unlocked so I can flash and configure it please? Is there some other wiring outside of the guide that I am missing? Also can anyone confirm the options that should be enabled to trigger heated seats, remote defrost and heated mirrors? Thanks

1

Why my remote do not open my doors after my car remote started

My 16 impala starts fine with my remote by i cant open my doors with my remote when it is running,

0

2018 Camaro Manual Transmission

0

2011 chevy cruze step 5 will not change from yellow to red just stays yellow

2011 Chevrolet Cruze, standard switchblade key with ignition cylinder on column (not push to start). Using EVO-GMT1, with the t-harness. Only wire I have wired to the vehicle for now is the brown wire on the 5 pin connector, and that is spliced into the number 1 pin at the dlc for can bus. I can get programming to step 5. I have hit the program button 5 times, and it will flash 5 times in 4 sequences, and then stay on yellow when its done. When i turn the key it stays yellow and nothing happens. I do not want any other feature this offers, except 3 lock remote start. I have verified switching 0-3v at the brown terminal with key on, and have wired it multiple ways to verify it's not something I did. I was able to get it to turn red once, turned the key off, removed the key, waited 5 seconds, and turned the key back on and it stayed red. I am a gm technician and very familiar with these vehicles but I can not get this thing to program.

12/08/2017