English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

24/12/2020

 Jeep Josh Payne (130Pts.)

0

Remote started stopped working... now getting 5 blinking red lights with hood trigger disabled.

I installed a EVO ALL on my 2011 Jeep Liberty. It worked about 10 times, then it stopped working. Unit now blinks blue when I click the lock button three times followed by 5 red blinking lights. I have disabled the Hood Trigger option and reflashed. I'm still getting the same response. I am in the 'Run' position on my 'vallet' switch... Not sure what other options to try. what is most puzzeling is that this starter worked... then it didn't... and doesn't. Any help? or ideas?
Connectez-vous pour répondre Voir 1 réponse(s)

31/10/2018

 Jeep eman lluf (130Pts.)

0

2014 Cherokee Doesn't Remote Start

2014 Jeep Cherokee, Latitude, 3.6 AWD.

Programing was succesful. Dark blue wire (from 20-pin) grounded. Blue light flashes when lock button is clicked on fob (majority of the time).

Clicking lock 3 times does nothing. I haven't gotten it to do anything as of yet.

Did I accidentally puty it in valet mode (how would I know)? How should I proceed?

Thank you

 

<!-- Used for easily cloning the properly namespaced rect -->
Connectez-vous pour répondre Voir 1 réponse(s)

24/02/2018

 Jeep MILTON DURANGO (160Pts.)

0

2017 wrangler no blinking when turn key

Hi I have a 2017 Wrangler and i connected the t harnes,hold button,plug black ,wait for solid blue, plug everithing else and when I turn the key it wont blink, try it 3 times and nothing,do i supoced to cut a wire or ist a problem with the unit, i got the evo chrt5, o and i have an alarm thanks
Connectez-vous pour répondre Voir 1 réponse(s)

06/01/2018

 Jeep Bryan Richardson (130Pts.)

0

How can I add siren and proximity/shock to my evo all

I’ve searched the support section, I have read guide 16221. I want to add a siren with warning chirp and alarm siren and proximity/shock sensor to my Jeep Wrangler using evo only. Please advise Parts needed, preferably Fortin brand. And how to do it. 16221 as well as the install instructions for my CHRT5. Please help, anyone in NC I will come to you for help.
Connectez-vous pour répondre Voir 1 réponse(s)

15/10/2017

 Jeep Mark Jenks (180Pts.)

0

Factory alarm isn't disabling when using RF Extender

I've had the EVO-ALL and T-Harness installed in my 2008 Jeep Wrangler (Standard key) for a few years now and it has worked without issues. It works with the factory remote (3 lock to start, 3 lock to stop). It is setup to unlock/lock/relock when remote starting, and handles the factory alarm the like it is supposed to. I have added a Axxess AX-RF2 2 to the EVO-ALL and setup all of the RF options using my Flash Link. I am using the 4 Pin D2d Data Cable Y Splitter. Connected wires are the Yellow, and brown/white running lights. When I use the RF remote, it will lock, unlock, start and stop, but it will not shut off the factory alarm. So it will trip the alarm every time. I've been through just about every option in Flash Link and and can't get it to disable the alarm with the RF. Even with the RF, the factory remote continues to work without issues.
Connectez-vous pour répondre Voir 2 réponse(s)

15/10/2017

 Jeep Mark Jenks (180Pts.)

0

Factory alarm isn't disabling when using RF Extender

I've had the EVO-ALL and T-Harness installed in my 2008 Jeep Wrangler (Standard key) for a few years now and it has worked without issues. It works with the factory remote (3 lock to start, 3 lock to stop). It is setup to unlock/lock/relock when remote starting, and handles the factory alarm the like it is supposed to. I have added a Axxess AX-RF2 2 to the EVO-ALL and setup all of the RF options using my Flash Link. I am using the 4 Pin D2d Data Cable Y Splitter. Connected wires are the Yellow, and brown/white running lights. When I use the RF remote, it will lock, unlock, start and stop, but it will not shut off the factory alarm. So it will trip the alarm every time. I've been through just about every option in Flash Link and and can't get it to disable the alarm with the RF. Even with the RF, the factory remote continues to work without issues.
Connectez-vous pour répondre Voir 2 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer