Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Owais Jan

Joined on the:

Jan. 29, 2014

Score

380

Comment(s)

23

Voted question(s)

0

Voted answer(s)

1

Votes up

0

Votes down

1

Votes up received

4

Votes down received

0

Recent Activity

Question(s) asked

4

Answered question(s)

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question
RECENT ACTIVITY QUESTION(S) ASKED ANSWERED QUESTION(S) COMMENTED QUESTION(S)

23/02/2014

 Dodge Owais Jan (380Pts.)

1

Remote starter is too quick

Generally i have a habit of staring the car after all the bulb check, throttle check, fuel trim is stablized, however when i do a remote start, the module just kicks off the car befor all that completed. this has happened couple of time with me, while doing a remote start, the moment interior gauge lights come up the starter straight away starts the car, resulting in slugish start, sometimes car kindof dies, with struggling starter and come back to normal. is there any way i can create a delay to remote start the car once all pre-start calibrations are done by the vehicle? Service:--001A06239902 Dodge charger 2009 V6
Login to reply View 1 answer(s)

18/02/2014

 Dodge Owais Jan (380Pts.)

1

What is External Input?

Evo all, installation guide for standalone remote start shows, Yellow/Black wire as external input. what does that mean? and do we need to connect 1k ohm resistor for parking light? which wire i can tap for parking (-), any place under the dash? I also need to know if there is a +12V switched ignition supply, i need this to power up my rear view auto dimming mirror? Thanks.
Login to reply View 1 answer(s)

12/02/2014

 Dodge Owais Jan (380Pts.)

1

Automatic door lock on dodge charger 2009

Hi, Recent news from Fortin shows that, eveo-all can be used as a standalone alarm system, meaning, no need to buy a alarm unit. my question is, has this feature been released in the software version or we need to buy a new hardware? secondly, my car doors never lock automatically after i leave the car in the parking, is there any way i can configure this from EVo? Thnaks
Login to reply View 1 answer(s)

10/02/2014

 Dodge Josh Knapp (210Pts.)

1

evo-chrt4 error in manual, or wrong harness with unit?

I am working on a 2008 charger, chose to use the evo-chrt4 for stand-alone installation. In the manual that came with the evo-chrt4 it says "for vehicles 2010 and less cut the vehicles ignition" which is fine. but in the manual it shows a picture of the "YELLOW" wire being in the t-harness.. my t-harness does not have a yellow wire. i called and all the guy could tell me was that i had the wrong harness cause only the t2 harness is supposed to have the YELLOW wire.. i just checked the vehicle, it does not have a yellow wire.. So. according to the instructions i am supposed to cut a non-existant yellow wire in the T-Harness?!?!? I have looked over the site fairly well, and have seen in all the instuctions pertaining to the t-harness that there is supose to be a yellow wire. i have also found that this wire being cut is needed to allow you to shift the the car from park. I have verified the part number listed on the t-harness is "evo-chrt4" the installation guide that came with the unit is revision 20130215(which appears to be the newest revision). and the service number on the evo all that i am using is 001a06 238084 (not that the service # matters as i feel that the error is in the manual, and not something to do with the unit.. also i could not find a service number on the t-harness, is there one? thank you for you time.
Login to reply View 1 answer(s)

10/02/2014

 Dodge Owais Jan (380Pts.)

1

IS hood pin necessary for the stand alone remote start?

Hi, after ordering the EVO-all with THAR-CHR4 for dodge charger 2009 V6, the seller confirmed that module has the latest Firmware and has option 15 enabled for remote start. I have installed the device, which was the easiest task ever. as per the manual, yello wire from T harness goes to the pin 1 on 20 pin connector and Dk blue wire to the hood pin, dont have doot pin in my car??? completed the installation and was able to program the module successfuly as explained, however no remote start after 3x lock??? what could be the reason and how do i fix this? thanks
Login to reply View 1 answer(s)

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue