Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping



Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question


Lights not coming on on evo one

No power to evo one on a 2016 4Runner. I already check all the wiring and there's power coming from the ignition harness. But when I try to program it there is no lights coming on at all on the evo one.


Interior lights are coming on and off, radio on and off, cluster on and off

When remote start is activated, the interior lights will come on and go off when Remote Start is activated. They do this every 15-20 seconds/ the radio comes on and goes off/ the IPanel splash screen comes on and goes off/ they do it separately from each other. Happens the entire time Remote Start is in control of the vehicle. Once I retake control, the interior lights behave normal, radio normal, IP cluster splash screen normal. I have a 30 second video if you would like to see. I do not recall this happening when I installed it. I only noticed it a few days ago. All wiring was soldered, except for the 3 1ohm resistors to the push button start switch. 2021 Sienna Hybrid EVO One Serial # - its installed in the vehicle.


2016 Toyota Corolla Evo One

I have used the Toy 8 Harness that came with the Evo One,Module (TOY 8 79/xx/1.xx C1, D5 38.2 Progam Lock). I followed all the steps and when I plug the 20 Pin Connector in the Evo Module, the noise sounds and the dash board warning message says, TURN LIGHS OFF and when I try to Press the button 10 times, the RED and BLUE LEDs fade out by the time I get to 6. I can't get Pass Step 3! I reset it a few times and still the same thing! I switch the Pins and try to use it as a TOY 3 Harness and the same Thing! I even Hard Wired the module using the Diagram and still the same thing! I'm thinking this was a bad Module from the beginnig! I have listen to TECH Support ideas and tried them and nothing works! I've made 7 attempts on wire this Evo One, trying different ways and the Module keeps doing the same thing every time. I'm ready to give up! Any idea, why this Warning Light coming on? Do this warning light be the reason why I can't ger pass Step 3?


2016 Toyota Corolla with H key,

After following the diagram and I go through the steps! When I go to plug the 20 Pin connector in the EVO ONE, it makes a noise like the lights are left on and the Dash Board warning say's TURN LIGHTS OFF! When I unplug the 20 Pin connector, the noise goes awayand the dash bord warning for TURN LIGHTS OFF, goes away! I try to program the EVO ONE Module with the noise and TURN LIGHTS OFF, by pressing 10 times, the light stop around the 5th to 6th press and it won't let me get pass Step 3. I reset the Module and did and Master rest and still have the same problem!


2013 Tacoma Evo one lights won't turn off after time out until doors are opened

Everything work except when remote starter times out the lights stay on and wind go off unless the door is opened


Auto lights

I am considering purchasing an EVO One with the TOY2 T-harness. I have a 2011 Tundra SR5 TRD. I see from the instructions that there is a wire for the Auto Lights. My truck does not have "auto lights", should this wire still be connected? Thanks.


Location of light switch harness on 2009 Toyota Camry XLE

Im looking to find the location of the light switch harness on my 2009 toyota Camry so that I can hook up the parking lights to my remote start system. Is this harness on the front side or back side of the BCM? Is it located at the BCM at all? Thanks for your help. -Keegan G

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue