Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

02/12/2017

 Nissan Alex Mello (160Pts.)

0

Evo one won't remote start

im reposting this question because my response was a little delayed. 

I have a evo one remote start syesten in my 2012 Nissan Xterra. I installed it with with the T-Harness, install guide 33161. I also have the Fortin RF642W RF Remote Kit With Two 4-Button, 2-Way remote installed.  The module programs to the car but the remote start does not work. the lock and unlock function works properly, the blue LED on the module will light up for both lock and unlock, but when I press the remote start nothing happens. No LEDs on the module light up, but the remote will flash green and beep. the red led under the yellow loop does not light up either. I also updated the module with the flash link updater,  and cut the yellow loop for the automatic transmission. Any help would be apriciated. thank you

Login to reply View 1 answer(s)

08/11/2017

 Nissan Alex Mello (160Pts.)

0

Evo One programs but won't remote start

I have a evo one remote start syesten in my 2012 Nissan Xterra. I installed it with with the T-Harness, install guide 33161. I also have the Fortin RF642W RF Remote Kit With Two 4-Button, 2-Way remote installed.  The module programs to the car but the remote start does not work. the lock and unlock function works properly, the blue LED on the module will light up for both lock and unlock, but when I press the remote start it seems that the module does not recive the signal. No LEDs on the module light up. I also updated the module with the flash link updater,  and cut the yellow loop for the automatic transmission. Any help would be apriciated. thank you

Login to reply View 1 answer(s)

04/07/2017

 Nissan Josh Hunt (130Pts.)

0

EVO One only shows yellow light on ignition on, wont remote start

I have a Nissan Xterra 2007, I purchased a EVO One with T-Harness and RF642W RF Kit. I'm using install guide 33131 for EVO one. I wired per instructions with A1,A2,A3,A8,A15 | E harnes by T-Harness, C3,C4, and D6,D4. D1 & D3 do not plug into anything and have been set aside. Held down Bypass Prog Button when inserting 6-pin power plug. I let LED cylce through once and waited for blue light and release bypass prog button and pluged in 20-pin, 6-pin bypass relay, 5-pin can bus, and 4-pin data link ant while the light stayed blue. I insert key into ignition chamber and turn to ON. Blue goes off then flashed blue. I turn key to off. Programming should be complete. 3X lock on OEM remote does not remote start. I insert key into ignition and turn to ON and the EVO One lights up yellow. I use the flashlink to update bypass to 72.27 and the remote start to 1.21. In bypass I enable C1 & D2. EVO still does the same thing when pluged into vehicle. I try using programming button but holding it down for 1+ minute with no horn beep. I suspect wiring was not correct. I double checked and have CAN-high and CAN-low correct. A1 is on (+) ignition (Pink-E5). A2 & A3 are on wiring diagram pin 14 & 13 but on vehicle BCS/BCM manual terminal is 8 & 7. A8 did not corispond with Wirecolor.com picture, image shows incorrect junction terminals for US version of Xterra. voltmetered 4 different plugs and no luck. According to vehicle BCS/BCM manual, driver door command is a Gray wire at M19 harness pin 47 next to 40-pin harness. When locking and unlocking the EVO one does not light up. I can't tell if OEM alarm is being set by Cars BCS/BCM or if it by the EVO One but the alarm does activate on door trip. Remote Start Programming: 2.3 | 3 (1) | 4.1 | 6.3 | 7.1 | 8.2 | 9.1 | 11.1 &11.4 | 12.1 | 13.2 | 14.2 | 15.2 | 16.5 | 18.1 | 19.1| 20.1 | 21.1 | 24.1 | 25.1 | 26.1 | 29.1 | 30.1 | 31.1 | 32.3 | 33.1 | 34-OFF-OFF| 35.1 | 36.2 | 37.1 | 38.1 (38.3-Off) | 39.1 Bypass Programming: A1-A11 - ON | B1-OFF| C1-ON| D2-ON| D3-D6 -OFF Unit Options : D.1 | D1.6 | H1 are enabled. I have master reset both side of EVO-One and started fresh with first paragraph and no luck, just same results. Any thoughts on where to look for the issue. I can grab field mesurements if desired.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue