Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

11/10/2020

 Ford Jaeden Hudson (340Pts.)

1

Fort2 programming issues

Trying to program my 17 f150 std key w/ keyless. I get to the point where it has me press the button 8 times. After I do that I put the key up to the ignition cylinder (not in it) and when I press the button, nothing happens. The red/blue lights stay on solid and the truck does nothing. I programmed the module with the latest firmware and other firmwares with no success. All connections have been verified. EDIT: Found out I had a bad connection however I have a new problem. After going through the programming sequence for the second key, after the ignition shuts off, the red LED flashes. When going back to the computer I get a message saying the immobilizer data received from the module is incomplete. I have tried the entire procedure 3 times with the same result. EDIT 2: I got it to go through all the steps. New issue now. When attempting to start the truck via the RF kit, I get a red light, then red/yellow light. They go out. Then I get red then red/yellow again. After that I get 3 red flashes and nothing else happens. The starter does not respond to 3x lock, although I can not remember if I disabled it or not.
Login to reply View 2 answer(s)

11/10/2020

 Ford Jaeden Hudson (340Pts.)

1

Fort2 programming issues

Trying to program my 17 f150 std key w/ keyless. I get to the point where it has me press the button 8 times. After I do that I put the key up to the ignition cylinder (not in it) and when I press the button, nothing happens. The red/blue lights stay on solid and the truck does nothing. I programmed the module with the latest firmware and other firmwares with no success. All connections have been verified. EDIT: Found out I had a bad connection however I have a new problem. After going through the programming sequence for the second key, after the ignition shuts off, the red LED flashes. When going back to the computer I get a message saying the immobilizer data received from the module is incomplete. I have tried the entire procedure 3 times with the same result. EDIT 2: I got it to go through all the steps. New issue now. When attempting to start the truck via the RF kit, I get a red light, then red/yellow light. They go out. Then I get red then red/yellow again. After that I get 3 red flashes and nothing else happens. The starter does not respond to 3x lock, although I can not remember if I disabled it or not.
Login to reply View 2 answer(s)

17/09/2018

 Nissan Stephen Puckett (160Pts.)

0

EVO ALL ONE programming issues

During programming of the EVO ALL in ONE the yellow light flashes and when I install the key to get the red and yellow solid light the blue light also comes on immediately solid and never goes out. So all leds stay lit solid at this point and I can go any further.
Login to reply View 1 answer(s)

06/05/2018

 Ram wizzled (130Pts.)

0

not programming?

I'm trying to program my EVO-ALL for my 2016 Dodge Ram with the tip start key. After pressing the programming 4x and the light turns to solid yellow it says "insert key" and the light should turn to red.  I insert the key and nothing happens.  I've flashed the module to 74.37 and still nothing.  I have master reset it and also programmed the can-bus  and the blue light stays solid on canbis programming. Any ideas?

Login to reply View 1 answer(s)

10/03/2018

 Hyundai Franck Ah-Kane (300Pts.)

0

Evo One Can Bus Data programming not flashing blue?

Hi all, I have installed the evo one inside my Sonata Limited 2016 PTS and went through the procedure outlined in the following page: http://fortin.ca/en/vehicles/hyundai/sonata/2018-push-to-start/troubleshooting.html Step 1: The module does not program correcty. Step 2: Step 5-6. Step 3: Blue led does not flash properly. Essentially, in step 5, when I start the ignition to on, the red LED flashes 10 times. Up to this point, everything is fine. Subsequently, instead of the blue LED flashing, I get both red and blue LED lighting up and remain as is. It only turns off when I turn off the ignition. I double checked my wiring but it does not seem to be the case. Would you have any suggestion? Best regards, Franck
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue