Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

16/03/2015

 Buick Hui Zhou (130Pts.)

0

Regal 2010 on EVO ALL with THAR-GM1V2 programming fail

My car is Regal 2010 flip key with auto transmission I got EVO-All and THAR-GM1V2, everything is well installed. Firmware is upgraded to latest version of this car. When I follow the programming guide step4, that is a long step, some actions requires to be finished within 5 second. When I finish step4 within 5 seconds, the yellow light keeps on and red light flash rapidly, which is differenct as guide shows. Please help. What should I do? Add more info I want to use it with oem remoter. The issue I described above was follow the programming guide. And it was not success as I mentioned. Then I tried to follow the decryptor guide. It's also difference as the guide shows. In the guide the last status should be blue light flash rapidly then remove the key blue light flash slowly. In my case the blue light keep light on before and after remove the key. However I still finish the whole process with flash link updater. When I reconnect the 4-Pin connector back after all the remaining connector, both red, yellow and blue light keep flash. I don't know whether the status is correct or not. When I push unlock button 3 times, nothing happen. Any more info needs, please let me know.
Login to reply View 1 answer(s)

27/01/2015

 Buick Mike Rogers (270Pts.)

0

lock/trunk release

2004 Buick Regal, evo-all service # 001A06453856 firmware 4.06, Avital 4103 RS. I decided to use the data-link so I changed the protocol on the evo and RS to D2D. Everything works except lock and trunk release. When I press the unlock the doors unlock the evo blue and the red led on the RS flash on then off. When I press the lock button the yellow led briefly flashes on and off then the red led flashes on and off, the RS led just blinks until I press the unlock button again. There is no response from pressing the trunk release, no lights nothing. After I updated the firmware other than changing the data-lick protocol to D2D I think I left everything else in there default settings.
Login to reply View 1 answer(s)

16/01/2015

 Buick Mike Rogers (270Pts.)

0

Will firmware 4.18 work with a 2004 Buick Regal?

The evo-all that I have has the 4.18 firmware hardware vr 6.Looks like I will need the 4.06 for a 2004 buick Regal,just need someone to confirm that for me.Thank you
Login to reply View 1 answer(s)

15/01/2015

 Buick Mike Rogers (270Pts.)

0

Parking light flash relay.

2004 Buick Regal-evo-all-Avital 4103 Do I need a relay for the parking light flash feature? Do I set the 4103 parking light flash jumper to (-) or (+) ? Thank you
Login to reply View 1 answer(s)

23/11/2014

 Buick Brandon Williams2 (130Pts.)

0

Programming step 5, yellow and red lights just flash

2012 Buick Regal GS PTS, EvoAll stand alone installed using guide 9901. I get to step 5 of the programming sequence and when PTS button is pressed the yellow and red lights both flash?
Login to reply View 1 answer(s)

19/02/2014

 Buick Joshua Bohling (140Pts.)

1

Which wires for 2013 Buick Regal PTS

I've read that for the 2013 Regal push-to-start, the t-harness is needed. Is this true? I have a manual transmission. If the t-harness is not used, which wires actually need to be hooked up? Only the solid black lines on the diagram? I would of course be tapping into the factory starter (since it's push to start anyways). It seems as though some of the solid black wires on the diagram are supposed to be run to an aftermarket starter system, and not interface at all with the EvoAll (such as the +12V coming from the vehicle's pin 1 in the blue connector), which makes it seem as though I won't even be using all the solid black wires on the diagram either. I've also read that the diode indicated in the instructions is not neccessary. Is that accurate? Finally, the instructions indicate that I need to cut a wire in the factory harness. Is this accurate? If so, is there any other solution that prevents the need to cut a wire? Warranty issues would prevent me from straight up cutting a wire in half. Thanks for your help.
Login to reply View 1 answer(s)

05/11/2013

 Buick ARturo MEza (360Pts.)

0

evo-all with thar-gm1v2 Buick regal 2012 manual

Im trying to install astand alone evo all with the t harness in my buick 2012 manual transmission. What guide should I use is seen confusion when you go to the T harness, I can fond wehre to install the resistors and the diode. And when I follow the evo-all guide It does not say anything about the t harness.
Login to reply View 1 answer(s)

15/11/2013

 Buick ARturo MEza (360Pts.)

2

Can I use a T Harnes in my Buick regal 2012 push to start

Can I use a T Harnes in my Buick regal 2012 push to start?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue