Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

18/01/2023

 Ford Todd Lusby (130Pts.)

0

2010 ford escape KEY-OVERRIDE-ALL

I'm installling the KEY-OVERRIDE-ALL with a DEI remote start. When I attempted to program prior, I would see the LED start flashing, but programming didn't complete. Now when I attempt to program, the LED on the module stays on and the security light on the dash flashes rapidly. I've confirmed I have 12V on Red, Ground on Black, Ignition on Yellow, and remote start staus on Blue. Is there anything else i should try on this module? The module was purchased new in December and hasn't been installed in another vehicle.
Login to reply View 1 answer(s)

25/08/2019

 Ford Jamie Murray (140Pts.)

1

evo-all on an escape doesn't initiate a start signal

2016 escape with an evo-all unit. the unit will not give a start signal on remote start. it detects the remote 3x lock (ie. blue light x3) but no red light. as per another suggestion the unit will give a red light when i ground the dk blue wire(ground while running) indicating that the unit is progammed correctly. what should i be checking next?
Login to reply View 1 answer(s)

19/12/2018

 Ford Mike Turner (140Pts.)

1

Programming evo-all 2010 Ford Escape

When trying to complete programming the engine doesn't come on. The dashboard lights up, the ignition seems to initiate, but doesnt turnover, and a security light in the bottom left of the dash flashes. The module flashes red about 10x and then all lights on the module go out completely.
Login to reply View 1 answer(s)

05/02/2018

 Ford Darren Asuncion (920Pts.)

0

2010 Ford F150 - PATS key error on first remote start attempt with EVO-All and Compustar CM-4200DX

I used the decryptor and the 1-key programming method on my 2010 F150. Everything seemed to go smoothly, took about 15 minutes to decrypt the key. I've got soldered/heatshrink connections throughout my installation. When I hit the remote start button on my Compustar CM-4200DX, the dash indicators light up like it is attempting a start, but the PATS warning light flashes rapidly (same as if you have an invalid/non-programmed key) and starter does not engage. The Compustar tries a second time, which again - all the dash lights come on as you would expect, but this time the PATS warning light stays on solid (just like it would if you used the key) and the vehicle starts up successfully. Not knowing if the Compustar module could "talk" to the EVO-ALL, I used the hardwire method for the install instead of data-link. I double-checked to make sure the EVO-ALL was getting a proper signal to the GWR, START, Ign, 12v+, and ground wires. Everything works just fine, except that the Compustar module has to try twice before the truck will start.
Login to reply View 1 answer(s)

08/01/2017

 Ford Pieter Van Zyl (130Pts.)

0

2014 Ford F150 Wont Start

    Evo-Fort1 2014 Ford F150 Stand-alone Install CAN Lo and Hi connected Lt. Blue, Lt Blue/Black and Yellow/Black wires from 20 pin connector connected to T-Harness Options A1-A11 are On Options C1 & D1 are On All Other options are off When dark Blue wire from 20 pin connector is grounded, nothing happens. Evo-All may not have programmed successfully.  Below are my steps
      Enter programming mode (hold black button until blue& red is on) Insert first key (amber light turns on at this point) Turn first key to run, wait 3 seconds Remove first key, install second key, turn to run, wait 3 seconds (Amber light stays on the entire time. Remove second key, Install first key, turn to run. Blue and red flash rapidly approx 10 times Blue stays on for about 3 seconds Blue turns off for about 5 seconds Blue flashes rapidly about 5 times, then amber turns on solid.
    When pressing lock 3x, blue light flashes with each lock, then red light turns on solid for about 10 sedonds, red light turns off for about 10 seconds, then red light turns on solid again and does not turn off. Vehicle does not start. Key in ignition is not mimicked either.
     

Please help.

Login to reply View 1 answer(s)

15/11/2015

 Ford Amy Harleson (130Pts.)

0

Evo-All installed and working on 2014 Ford F150, but now truck won't crank with key

The Evo-All was installed, and the remote start function works correctly without issue, however now if you try and start the truck with just the key and not using the remote start function it will NOT crank at all. The lights, radio and the like all come on but the key does not turn over and the engine does not start unless using the remote start function (hitting lock button 3 times).
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue