Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

01/02/2020

 Ford Todd Aker (200Pts.)

1

Can not get past step 6 no blue light in step 7

I have a 2010 ford escape. auto trans and 6cyl engine. I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be. HELP?
Login to reply View 2 answer(s)

01/02/2020

 Ford Todd Aker (200Pts.)

1

Can not get past step 6 no blue light in step 7

I have a 2010 ford escape. auto trans and 6cyl engine. I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be. HELP?
Login to reply View 2 answer(s)

09/11/2020

 Ford Steve Schoen (130Pts.)

0

Remote start wont program when key in run position

2017 Ford explorer using Evo All and Fort3 harness. Used Flashlink and updated firmware to latest for the Explore. Used the suggested setting. I got it all hooked up. Followed instructions and get the solid blue light. When I turn key to run position nothing happens. Blue light stays blue and never starts to blink rapidly to indicate programming. What have I missed?
Login to reply View 1 answer(s)

01/02/2020

 Ford Todd Aker (200Pts.)

0

Can not get past step 6 no blue light in step 7

I have a 2010 ford escape. auto trans and 6cyl engine. I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be. HELP?
Login to reply View 0 answer(s)

30/12/2018

 Ford Mathieu Levac (240Pts.)

1

F150 pairing Blue light doesn't flash when sequence is followed

Hello, i recently bought a OMEVOALL version 6 firmware 71.34 OMEVOFORT preloaded with a THAR-Ford3 T plug for my 2018 f150. Following your instruction guide and this online video https://www.youtube.com/watch?v=3bpmiYwslSo , i am unable to get the blue light to flash after turning the key to the on position like in your guide and the video. My truck is equipped with a stock hood pin sensor. Any assistance would be appreciated.

Login to reply View 1 answer(s)

08/07/2018

 Ford Josh Miedema (130Pts.)

0

Program went well but blue led will not blink when hitting the lock/unlock buttons for 2016 Ford explorer.

Program complete but the blue led will not light up when using the lock/unlock on remote. Can not remote start it.
Login to reply View 1 answer(s)

03/07/2018

 Ford chris rosado (140Pts.)

1

2017 Ford F-250

Vehicle 2017 Ford F-250 

Product. Evo-all Service # 001a06749339 That-ford2 t harness  Install guide # 59421   Installed according the install hour minus the lights . I don’t want my lights to work . Having problems programming. I get all the way to the point of the the truck ingnition turning in and that’s it. After that the blue LED does not flash or do anything after the ignition is on.  The truck has a factory hood pin as well and the hood is closed .  I also tried to reset  the unit and start over in the reprogramming, that didn’t help. 
Login to reply View 1 answer(s)

16/05/2018

 Ford Mike Stimson (130Pts.)

0

2016 F150 EVO-One Blue LED flashes continuously while programming

I installed an EVO-One using the THAR-FOR3 in a 2016 F-150 with push to start but haven't been able to program the key bypass. Following steps 1-4 for the key bypass programming in the guide, I get a solid blue LED light, and then when I push the start button, the blue LED continuously blinks. Any suggestions?
Login to reply View 1 answer(s)

28/10/2017

 Ford Joshua Clinard (130Pts.)

0

2010 Fusion. Getting solid RED LED but no yellow LED when in on position.

to start off im not really a car guy but this seemed pretty easy but anyways i just went to install the EVO-FORT1 into my 2010 Ford Fusion Sport and i put the data pin in and get the solid blue LED then go back and plug the red plug in and get the solid red LED. after all of that i go to put the key into the on postion but it stays solid red. i am asummng that it has something to do with the other plugs that has all the wires on the end?
Login to reply View 1 answer(s)

07/09/2017

 Ford spank monster (130Pts.)

0

Blue light will not rapid flash during programing

2010 f350 6.4 evo one during programing the blue light is on, turn the key on and the blue light turns off instead of flashing, turn key off blue light comes back on. I have done the hard reset on the evo one, checked wiring, tested can high and low at white evo connection both show around 2.5 volts, the yellow wire at evo connector shows 12 volts with key on, 0 volts with key off. and i have tried switching can high and low wires.

Login to reply View 1 answer(s)

09/08/2016

 Ford travis peterson (390Pts.)

0

blue led doesn't light with lock/unlock after successful dcryptor update

My vehicle: 2014 ford escape (non-push button) with oem remotes Dcryptor programed successfully, and updated device. A1, A3, C1, D1, and D1.6 options are ON. All other options OFF. Can test: blue led ON with key out, and OFF with key in and ignition. led never blinks. When lock/unlock is pressed: no LED's light up & car will NOT remote start. What am I missing? Any help is much appreciated. I'm stumped.
Login to reply View 1 answer(s)

05/07/2016

 Ford derek g (342790Pts.)

4

EVO-FORT1 wiring information

The biggest question I hear when it comes to the EVO-FORT1 combo is that the module "will not program"....9 times out of 10 it is that the 3 main connections were left out!!! So below is the 3 types of connections that are done between the evo and the t-harness.

TYPE 1 CONNECTION

In the above image commonly used on the 40 bit type systems its basically match the colors between the t-harness and the 20 pin connector. Be sure to isolate the Yellow/Black wire from the T-Harness as it is not connected.

Type 2 CONNECTION

In the image above commonly used on 80 bit systems we match the colors EXCEPT you are not connecting yellow to yellow rather the yellow/black from the t-harness connects to the yellow wire from the 20 pin connector and you isolate the Yellow wire in the T-Harness.

TYPE 3 CONNECTION

In the above image it is exactly the same as connection 2 but in addition to the Yellow/Black being connected to the Yellow of the evo-all, we are also connecting the Purple/Yellow along with the Yellow. Isolate the Yellow wire from the T-Harness.

Login to reply View 0 answer(s)

26/12/2015

 Ford shawn geer (80Pts.)

0

edge flashes red 10 times then blue 10 time then yellow once and doesnt start

after programming with keys it says to hold down programming button and it will flash 10 red, 10 blue and start but instead of starting it flashes yellow once and does nothing.
Login to reply View 1 answer(s)

15/11/2015

 Ford Daniel LeMoine (130Pts.)

0

2014 F150 installed EVO-FORT1 exactly like youtube video and blue light doesn't change when key is inserted?

Just installed EVO-FORT1 in my 2014 F150 which has the T-Harness and installed just like the Youtube video with the 2 cam wires wired and the T-Harness. I purchased this kit on ebay with it already flashed for my vehicle before it was shipped to me so I don't have that programmer. When I hold the button down and plug in the harness the blue light comes on and I let go of the button and plug in all the other wires. I then put the key in and turn and nothing happens the light stays on solid.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue