Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

07/02/2023

 Dodge Ahmed Ali (240Pts.)

0

Evo one CHR4 dodge challenger 2010 no any action only security light flashing

2010 Dodge challenger SRT with stander key and manual transmition Module programming okay blue light flash every press lock Remote start red light one and give 2 sound then off dashboard securty light flashing Evo one with Chr 4 T-Harness please help
Login to reply View 1 answer(s)

13/11/2021

 Dodge GREG ARNOLD (230Pts.)

0

2006 Ram 2500 Solid Blue Light goes out when ignition turns on during programing.

2006 Ram 2500 Solid Blue Light goes out when ignition turns on during programing. Answer: The fix for me was to only use the grey Can wire. i removed the grey with black stripe wire and i was able to finish the install.
Login to reply View 1 answer(s)

09/11/2021

 Dodge Shane Benjie (220Pts.)

0

Solid blue light...HELP!

2010 Dodge Journey- installing the evo all as a stand alone starter, updated to firmware 74.39 and using a T-harness CHR4. i've connected both yellow wires and cut the yellow wire and attached the yellow/green wire on the ignition side as per the diagram. I've checked the connection several times but each time I only get the solid blue light when programming, what am i doing wrong?
Login to reply View 1 answer(s)

05/02/2020

 Dodge P Mo (140Pts.)

1

2004 dodge durango evo-one thar-chr5 Blue light doesn't stop flashing

During programming when I plug in the white E 6 pin connector blue light goes out. When I turn the key on the blue light starts flashing. Doesn't stop flashing at step 6. After starting the vehicle with key it, the yellow light comes on and stays on. When i try 3x lock, the blue light flashes once per lock, but does not try to start.
Login to reply View 1 answer(s)

22/12/2019

 Dodge mervin dulce (510Pts.)

0

2004 Dodge durango evo one programming. blue light wont stay on on mode selection

So i hard wired everything. In the programming procedure. Blue light wont stay on. I checked everything is all in order. Does anyone know what is happening? Thanks
Login to reply View 1 answer(s)

16/08/2019

 Dodge Colby Sturrock (130Pts.)

0

Cannot get blue led in 2009 Grand Caravan

I cannot get the programming step. I have the t harness plugged in and the two yellow wires connect together like many tutorials? Is this incorrect? He do not want any other functions other than remote start.
Login to reply View 1 answer(s)

02/02/2019

 Dodge Todd Karlen (130Pts.)

0

Blue light shuts off when turning key to on position

2008 Dodge ram the blue light shuts off when I turn the key to the on position.
Login to reply View 1 answer(s)

14/12/2018

 Dodge Scott Harris (130Pts.)

0

Remote LED is flashing blue and nothing else happens.

My son who is 2 got a hold of my keys and started to press the buttons on the remote starter. Once I got my keys back the remote would not start the car but now just flashes a blue light.
Login to reply View 0 answer(s)

05/01/2017

 Dodge Zach Olson (130Pts.)

0

Blue light won't flash when put key in on position

Purchased preprogrammed evo for 2010 dodge ram diesel. Followed instructions to program key. Once you insert key into on position the blue light remains a constant blue. Not flashing
Login to reply View 1 answer(s)

05/12/2016

 Dodge Scott Roberts2 (180Pts.)

0

Wont program. No flashing blue light

I can't get my CHRT5 to work. I connected the 2 yellow ignition wires, and the green/red to purple for the MUX. Apparently this is all I need to do. Others on a Ram forum did this and got it to work. I'm thinking it might have to do with the programming with the module. The guy I bought it off of updated it for me, and turned on the 3x lock function. When I hold down the button and plug the data cable, I leave it on the blue light. I then plug everything in. Turn the key to on, and the blue light turns off. Then my dash lights flicker, and I get a check gauges light. Please help.
Login to reply View 1 answer(s)

05/12/2016

 Dodge Scott Roberts2 (180Pts.)

0

Wont program. No flashing blue light

I can't get my CHRT5 to work. I connected the 2 yellow ignition wires, and the green/red to purple for the MUX. Apparently this is all I need to do. Others on a Ram forum did this and got it to work. I'm thinking it might have to do with the programming with the module. The guy I bought it off of updated it for me, and turned on the 3x lock function. When I hold down the button and plug the data cable, I leave it on the blue light. I then plug everything in. Turn the key to on, and the blue light turns off. Then my dash lights flicker, and I get a check gauges light. Please help.
Login to reply View 1 answer(s)

01/09/2016

 Dodge William Thomason (130Pts.)

0

Blue LED does not flash 2014 Dodge Charger SE Step 10 turns off when PTS pushed Can Hi/Lo OK...Brake?

I have been through the programming steps 3 times. Was somewhat confused as to whether I should push on the brake (as in "hold down brake and push button to start" for normal starting) during programming steps so I tried both ways. Both times, all goes well until step 10 of the programming sequence. With the Blue LED on solid, when pushing the start button once to turn on the ignition, the blue LED turns completely off and does not flash. I read elsewhere in the Dodge FAQ where it was suggested to connect red/green A18 wire to brake pedal wire, but in my install guide (#12211 - Stand Alone for CHRT6 with T Harness for Automatic Trans Only), the connection diagram says to connect wire A18 to the parking light switch wire which is how I have it. Just to note, when I do not press the brake pedal during programming, the car goes to run position, but does not actually start whereas when I do press the pedal, it does. This seems to have no effect either way on the situation with Blue LED (behavior is same either way). I have double checked and can-bus hi/lo wires are correct and not reversed. Hardware version is 6, firmware is 74.25. Thanks for any advice you may have!
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue