Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

01/11/2020

 Ford Andrew Dick (130Pts.)

0

2016 Ford F150 with Fort 3 harness not starting truck after first programming

Have installed the Fort 3 t harness , Evo all has been flashed with Flashlink 4. Firmware 4.02 A11 off and C1 selected. Completed module installation and truck starts when pressing lock 3 times.(when reprograming module the truck always starts on first test only) Upon an second attempt to press lock 3 times results in module goes red, orange and then blue, truck horn honks.(no start) it tries to do this two times and then 3 red lights blink on the unit. When opening door truck warns of alarm going off unless i insert key. Please can you advise. Thnak you very much
Login to reply View 1 answer(s)

08/07/2019

 Ford Robert Smith (130Pts.)

0

2016 F150 XLT Std Key EVO-ALL w/ Fort3 Standalone Mode C1 & D1 Options Good--No Start

I am in the process of installing an EVO-ALL device with a Fort3 cable into a 2016 F150 XLT with standard key.

    The module programmed correctly. The hood is definitely closed. When attempting to remote start using a LOCK, UNLOCK, LOCK sequence the BLUE LED flashes once with each LOCK button press and twice with the UNLOCK button press. After the third (LOCK) button press the LEDs go through a flashing sequence that ends with a pause (no LEDs lit) followed by three quick flashes of the RED LED which I understand means NO TACH.


I verified that options C1 and D1 have been turned ON by doing the following:

    I grounded the A8 pin of the 20 pin connector.  The RED LED did NOT light so option D1 should be on. I momentarily grounded the A13 pin of the 20 pin connector.  The LEDs went through a flashing sequence very similar if not identical to the one that they go through when attempting a LOCK, UNLOCK, LOCK type remote start.  The flashing sequence ended with the same pause (no LEDs lit) followed by three flashes of the RED LED which I understand means NO TACH.

 

Any ideas?

Thanks!

Login to reply View 1 answer(s)

05/10/2018

 Ford Chris George (160Pts.)

0

2016 Ford F150 doesn't display run time after vehicle starts.

A network error comes in after a minute or so, but the vehicle is running ?
Login to reply View 0 answer(s)

05/10/2018

 Ford Chris George (160Pts.)

0

2016 Ford F150 doesn't display run time after vehicle starts.

A network error comes in after a minute or so, but the vehicle is running ?
Login to reply View 1 answer(s)

31/01/2018

 Ford Eric Bailey (170Pts.)

1

2016 Ford F150 Standard key Evo-All w/T-harness fort2

Won't program. All connections verified 5 times good. gets to the point of inserting 2nd key and removing it, ignition turns on red and yellow light on won't program can bus no blue light flash. Blue light at one time flashed after that but ignition didn't turn off and yellow and red light didn't alt flash. Should it take long between lights flashing? Very frustrated!!!!
Login to reply View 1 answer(s)

04/09/2016

 Ford Kelly Bochniak (340Pts.)

2

2016 ford transit 250 t harness not available yet for the evo all?

Was told by one of distribution dealers (Clutchfield) that the t harness-with plugs for the evo all is not available yet for the 2016 ford transit, needs to be all spliced in,if so when will it be?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue