Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

21/12/2021

 Chevrolet Victor Burisch (130Pts.)

0

2014 Tahoe EVO-ALL no crank

Have the EVO-ALL installed with T-Harness in a 2014 Tahoe. After car is shut off with the key and remote start is attempted vehicle will start as it should. Any other time you attempt to remote start the vehicle it will go through the motions and power on ignition but will not crank. it makes two attempts and then shuts down with the 3 light flash. the ignition powers on and then goes out as if it was going to attempt to start but it does nothing. if i restart the vehicle with the key, turn it off and attempt again it will rempote start one time
Login to reply View 1 answer(s)

04/01/2020

 Chevrolet DAVID BARNES (250Pts.)

0

2015 malibu no crank no start

I installed an evo all gmt1 in a 2015 malibu flip key. I used a flash link to update firmware and do the key dcryptor. I also have a 2 way lora 9 rf kit. The install and all programming of the unit went as it should. ( all lights and flashes correct ) However the vehicle wont start. It doesnt even attempt too. When using the 3x lock the evo all sees it ( flashes when the lock button is pressed ) then nothing. Also with the 2 way rf transmitter the evo all and antenna see it and the transmitter responds with green light and audible tune but the same result occurs after that. The car does not attempt to start. I have installed an evo all before so this is not my first install and I went over the programming of the unit and the keys / transmitter numerous times. Any ideas on what could be the hang up would be greatly appreciated. Thanks

Login to reply View 1 answer(s)

21/09/2019

 Chevrolet Derek Deines2 (190Pts.)

0

EVO ALL D4&D6 connection question - car wiring doesn't match directions

2009 Chevy Cobalt trying to hook up the D4 & D6 PK3 wires. Instructions say white connector & pin 2 is Red/White. My connector is black and the colors are 1 Red/White, 2 Brown, 3 Black/White, 4 Green, 5 Blank Do I still hook up pin 2 or the Red/White wire? I can't get the EVO ALL to program so wondering if this is my problem. Currently wires are connected to the Green wire in Pin 2
Login to reply View 0 answer(s)

04/07/2019

 Chevrolet Dimitrios Spanoudakis (180Pts.)

0

Module has no lights, unplug it all, plug factory harness back, truck doesn’t start.

Installed system yesterday on 2011 Chevy Express. Worked when the dash was apart. Tucked it all out of the way and reinstalled lower dash. Then it wouldn’t start. Look at the module and no lights appear. Tried with the key and nothing. Took it all out and replugged the factory harnesses on the ignition switch. Tried with key again and still nothing. Doesn’t crank. Fuel pump primes. Checked fuse box and all fuses are ok. What did this short out?? Desperation as this is my work truck. Please help.
Login to reply View 1 answer(s)

07/04/2019

 Chevrolet James Mayer2 (130Pts.)

0

2014 Chevy Cruze dash lights up but no crank

I installed my EVO All (Service# 001A06 853981) in my 2014 Cruze. When I push the OEM lock button 3x, the dash lights up but the car does not crank. All doors, trunk, and hood are closed. Options C1, D1, and D2 are all ON.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue