Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

03/02/2023

 Jeep Nev (130Pts.)

0

Jeep has power but does not crank?

I have programmed the unit sn: 001A07 415854 Evo All. Installed with wiring harness THAR-CHR4 (Both Yellow wires on the harness are connected together). Programmed the unit. All these went according to the documentation, correct leds and all.

My vehicle is a 2011 Jeep Grand Cherokee 3.0CRD Limited with Start Button

I do the 3x Lock Blue Led comes on every time I press the lock button. Then all power comes on, a few seconds later the red and yellow led is solid and the radio shuts off just like it does while it cranks but no crank??

What could I be doing wrong?

Many Thanks!!

Login to reply View 1 answer(s)

16/01/2022

 Jeep Andy Sicard (200Pts.)

0

2005 Jeep Grand Cherokee, Turns on but no crank, no start.

Installing Evo All, stand alone with Thar-CHR5 harness. Ignition and MUX wires are connected, module is programmed, key is programmed. Dash lights up, fuel pump buzzes but not start. 

With the harness, I connected the yellow-yellow (ignition), green/red-purple (MUX), and white/red-pink/orange (starter) wires. is there something I'm missing?

Login to reply View 2 answer(s)

16/01/2022

 Jeep Andy Sicard (200Pts.)

0

2005 Jeep Grand Cherokee, Turns on but no crank, no start.

Installing Evo All, stand alone with Thar-CHR5 harness. Ignition and MUX wires are connected, module is programmed, key is programmed. Dash lights up, fuel pump buzzes but not start. 

With the harness, I connected the yellow-yellow (ignition), green/red-purple (MUX), and white/red-pink/orange (starter) wires. is there something I'm missing?

Login to reply View 2 answer(s)

08/12/2021

 Jeep Shane Benjie (220Pts.)

0

2007 Jeep Compass, turns on but no crank no start.

installing Evo All, stand alone with Thar-CHR5 ignition and MUX wires are connected module is programmed, key is programmed bit no start. Dash lights up, fuel pump buzzes but not start. HELP?
Login to reply View 1 answer(s)

22/03/2019

 Jeep Douglas Chase (130Pts.)

0

2012 Jeep Compass Turns on but doesnt crank EVO All

2012 Jeep compass, programming goes through sucessfully but pressing lock 3x will turn on everything, but doesnt actually crank. Using evo-all chrt5 harness. have yellow wire joined together, thats only one hooked up.
Login to reply View 1 answer(s)

09/01/2019

 Jeep Brent Blunier (160Pts.)

1

'07 Jeep GC, MUX voltage, key on- no crank, verifying wiring connections

2007 Jeep Grand Cherokee Diesel Automatic, EVO-CHRT5 T harness, standalone F diagram. 74.07 firmware, 6.0 hardware, Bypass checked "on"  are A1,3,7 C1, D1, D2, all other options are checked "off". OEM key programming was successful. When I push lock 3X the ingition comes on but engnine does not crank. I checked ignition connection after lock 3x, the power consant (white /blue) =12v and starter cranking (white/red) = 11.9v. The MUX voltage (VOM on green /red and chassis ground)  with no key =4.19v, key in=3.61v, key on=.993v, crank =.36v.... when remote starting "key on" =1.05v, "key off"=4.19v, cranking = .40V. .. I also have error codes/warnings ( trans temp, 4WD system fault) that appear on dash when it tries to remote start.  I have attached pic of wiring to the ingnition connection. I'm questioning MUX voltage and correct wiring? attached pics. the wires are soldered to pins in connector

Login to reply View 2 answer(s)

09/01/2019

 Jeep Brent Blunier (160Pts.)

1

'07 Jeep GC, MUX voltage, key on- no crank, verifying wiring connections

2007 Jeep Grand Cherokee Diesel Automatic, EVO-CHRT5 T harness, standalone F diagram. 74.07 firmware, 6.0 hardware, Bypass checked "on"  are A1,3,7 C1, D1, D2, all other options are checked "off". OEM key programming was successful. When I push lock 3X the ingition comes on but engnine does not crank. I checked ignition connection after lock 3x, the power consant (white /blue) =12v and starter cranking (white/red) = 11.9v. The MUX voltage (VOM on green /red and chassis ground)  with no key =4.19v, key in=3.61v, key on=.993v, crank =.36v.... when remote starting "key on" =1.05v, "key off"=4.19v, cranking = .40V. .. I also have error codes/warnings ( trans temp, 4WD system fault) that appear on dash when it tries to remote start.  I have attached pic of wiring to the ingnition connection. I'm questioning MUX voltage and correct wiring? attached pics. the wires are soldered to pins in connector

Login to reply View 2 answer(s)

31/10/2016

 Jeep Kyle Green (140Pts.)

1

2010 jeep liberty ignition comes on but no crank

i have a 2010 jeep liberty hooked up to a fortin evo-all which is data link connected to a crimestopper rs3-g5 remote start. it worked for a while but than all of a sudden it wouldnt crank. my electronics and ignition would come on but it wouldnt start. when the car is started it has the orange light on and when its remote started the red and orange light is on. any tips?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue