English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

Owais Jan

À rejoins en date due:

Jan. 29, 2014

Points

380

Commentaire(s)

23

Questions votée(s)

0

Réponses votée(s)

1

Votes positifs

0

Votes contre

1

Votes reçus

4

Votes négatifs reçus

0

Activité récente

Questions demandée(s)

4

Question(s) répondue(s)

0

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question
ACTIVITÉ RÉCENTE QUESTION(S) DEMANDÉE(S)" QUESTION(S) RÉPONDU(S)" QUESTION(S) COMMENTÉE(S)"

23/02/2014

 Dodge Owais Jan (380Pts.)

1

Remote starter is too quick

Generally i have a habit of staring the car after all the bulb check, throttle check, fuel trim is stablized, however when i do a remote start, the module just kicks off the car befor all that completed. this has happened couple of time with me, while doing a remote start, the moment interior gauge lights come up the starter straight away starts the car, resulting in slugish start, sometimes car kindof dies, with struggling starter and come back to normal. is there any way i can create a delay to remote start the car once all pre-start calibrations are done by the vehicle? Service:--001A06239902 Dodge charger 2009 V6
Connectez-vous pour répondre Voir 1 réponse(s)

18/02/2014

 Dodge Owais Jan (380Pts.)

1

What is External Input?

Evo all, installation guide for standalone remote start shows, Yellow/Black wire as external input. what does that mean? and do we need to connect 1k ohm resistor for parking light? which wire i can tap for parking (-), any place under the dash? I also need to know if there is a +12V switched ignition supply, i need this to power up my rear view auto dimming mirror? Thanks.
Connectez-vous pour répondre Voir 1 réponse(s)

12/02/2014

 Dodge Owais Jan (380Pts.)

1

Automatic door lock on dodge charger 2009

Hi, Recent news from Fortin shows that, eveo-all can be used as a standalone alarm system, meaning, no need to buy a alarm unit. my question is, has this feature been released in the software version or we need to buy a new hardware? secondly, my car doors never lock automatically after i leave the car in the parking, is there any way i can configure this from EVo? Thnaks
Connectez-vous pour répondre Voir 1 réponse(s)

10/02/2014

 Dodge Josh Knapp (210Pts.)

1

evo-chrt4 error in manual, or wrong harness with unit?

I am working on a 2008 charger, chose to use the evo-chrt4 for stand-alone installation. In the manual that came with the evo-chrt4 it says "for vehicles 2010 and less cut the vehicles ignition" which is fine. but in the manual it shows a picture of the "YELLOW" wire being in the t-harness.. my t-harness does not have a yellow wire. i called and all the guy could tell me was that i had the wrong harness cause only the t2 harness is supposed to have the YELLOW wire.. i just checked the vehicle, it does not have a yellow wire.. So. according to the instructions i am supposed to cut a non-existant yellow wire in the T-Harness?!?!? I have looked over the site fairly well, and have seen in all the instuctions pertaining to the t-harness that there is supose to be a yellow wire. i have also found that this wire being cut is needed to allow you to shift the the car from park. I have verified the part number listed on the t-harness is "evo-chrt4" the installation guide that came with the unit is revision 20130215(which appears to be the newest revision). and the service number on the evo all that i am using is 001a06 238084 (not that the service # matters as i feel that the error is in the manual, and not something to do with the unit.. also i could not find a service number on the t-harness, is there one? thank you for you time.
Connectez-vous pour répondre Voir 1 réponse(s)

10/02/2014

 Dodge Owais Jan (380Pts.)

1

IS hood pin necessary for the stand alone remote start?

Hi, after ordering the EVO-all with THAR-CHR4 for dodge charger 2009 V6, the seller confirmed that module has the latest Firmware and has option 15 enabled for remote start. I have installed the device, which was the easiest task ever. as per the manual, yello wire from T harness goes to the pin 1 on 20 pin connector and Dk blue wire to the hood pin, dont have doot pin in my car??? completed the installation and was able to program the module successfuly as explained, however no remote start after 3x lock??? what could be the reason and how do i fix this? thanks
Connectez-vous pour répondre Voir 1 réponse(s)

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer