Questions & Réponses

2016 Toyota Corolla, H-Key, Manual. No OEM Alarm, No TPMS (and no wire for TPMS, no wire to pin location on plug). Installed EVO-One with Toy-8 and RFK942. Setup via wizard. Only wire T'd was for clutch bypass.

Completed a recent install but have a couple of issues I am hoping to resolve.

1) Automatic headlights won't turn off when setting reservation mode. Tried on door close, and also on lock. Believe it needs a door pin pulse which is connected via the harness. Is there a setting I am missing somewhere?

2) Once the Evo was installed, neither of my factory fobs work (even when not remote started). Unplugged the Evo (but left harness) and still no fobs work. Nothing lights up on the evo when pressing factory fob.

 ***Update***: Found a bent pin in my T-Harness when troubleshooting. I was able to straighten it back out, all fobs are working again. Stil have the issue with the headlights.

Thanks all for the help

I've installed the EVO-ONE with the RF441 kit and the THAR-ONE-TOY8 harness in a 2015 Corolla CE (auto, H-key, no OEM remote, no OEM alarm). Most of it seems to be fairly plug-and-play, but it doesn't seem to be picking up the horn nor the door pin switch.

It locks, unlocks, remote starts and stops just fine with the parking lights merrily blinking away, but it is completely silent - even if I press and hold the LOCK button for three seconds to send everything blinking there is no sound.

It also looks not to be picking up the door pin switch.

Am I correct in assuming that neither of these is on CANbus and both need to be wired individually?

The TOY3 harness documentation (ig_thr_bi_toy3-corolla_2014-2016_hkey_g_31341.pdf) seems to suggest that the door pin (-) needs a hard-wired individual signal (EVO ONE: -/Driver Door Pin Green/Red In/Out A18 to Corolla: pin 34 - white wire - on white 40-pin connector E3, fuse box) while every other document Fortin provides shows no such connection and unhelpfully labels EVO ONE A9-10, A16-20 simply as "Bypass config." with no further description and nothing connected. I'd installed based on the TOY8 documentation, which has no discrete individual connection to the door pin switch. The door is ignored.

Which is correct?

For the horn?

An earlier question "No horn chirp evo one 442 rf kit with a 2017 Tacoma H key ?" suggested individually hard-wiring Evo-One's two-ampère horn/siren relay (orange/black on the 20 pin connector) to the horn trigger (ie: the wire to the actual horn switch on the steering column).

Upon reviewing all of Fortin's Toyota-specific documentation, there seems to be nothing saying exactly where to connect this wire on the 2015 Corolla. Anywhere. (Including evo one: ig_reg_bi_toy-corolla_2014-2016_hkey_g_31301.pdf, ig_thr_bi_toy3-corolla_2014-2016_hkey_g_31341.pdf, ig_thr_bi_toy8-corolla-im_2014_hkey_a_71461.pdf) and the generic EVO and RF441 docs (dem-ug_en_generic_k_21471.pdf, fortin-rfk441-install-guide-68451.pdf) among others.)

None of these documents indicate that a hard-wired horn trigger needs to be connected to the vehicle to get the horn or the alarm and none say where to find the horn signal in the 11th gen Corolla; they list the individual EVO ONE pin (A7) but don't show it connected anywhere on the car.

A post on the12volt com's Toyota forum suggests "Horn Trigger: lt. green - dash fuse box, white 56 pin plug (3C), pin 49" as a candidate for the 2014 Corolla without pushbutton start; I presume "dash fuse box" is the BCM but which connector is this? Can it be hard-wired direct to EVO ONE pin A7 or does it need a relay?

Why isn't this wire on the 11th gen Corolla identified by name, number, position or colour in any of the Fortin documentation, and is the info from the outside forum still correct for the 2015 model?

On a 2015 Toyota Corolla LE (non-push-to-start) is there a benefit of using THAR-ONE-TOY8 over THAR-ONE-TOY3?

On a 2015 Toyota Corolla LE (non-push-to-start) is there a benefit of using THAR-ONE-TOY8 over THAR-ONE-TOY3?