Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Unable to program MyCar telematics module to EVO-ALL

When trying to learn MyCar telematics module to the EVO-ALL, at the point after switching the ignition ON when the RED & BLUE LED's are supposed to flash, they never do. I have waited upwards of 10 minutes, but they never flash. My MyCar app reads the GPS position of the car but Start/Stop and Lock/Unlock does not work. The telematics module LED's show that the module is connected to both GPS and Cellular. The OEM remote start works as it should with Lock/Lock/Lock. 2021 Toyota Corolla, Push Start, Automatic with T-Harness. EVO Serial N.: 001A07 220406 Any suggestions?

0

Alarm input detection myCar

Does anyone know how many pulse the alarm input detection on mycar need to see before it notify the app? Also is there anyway for me to use any aux option myxar have with an evo-all installed in 2014 camry pts. Thank you so much

0

2016 Tacoma Automatic - Push button - EVO-ONE w. MYCAR Telematics

Hi, I had succesfully installed the EVO-ONE and using factory fob for remote start; The MyCar unit arrived with instructions. install-guide-64631. Everything works per instructions until step 8; when I press brake and release and then turn off, I get several blinks of lights and Evo unit, not the "Once" that is expected. Mycar is online and I can see the unit, car voltage etc. It will just not learn to the EVO-ONE... I cannot seem to get past this step. STEP 8. LEARN THE TELEMATICS DEVICE TO THE EVO-ONE In order to communicate with the remote starter, the MyCar must be learned to the EVO-ONE. 1 - Cycle the ignition to the ON position. 2 - The YELLOW LED on top of the EVO-ONE should come ON. 3 - Press and Hold the EVO-ONE push button for 5 seconds. 4 - The parking lights and the RED LED on the side of the EVO-ONE will turn ON. 5 - Release the push button. 6 - Press and Release the push button 5x times. Everytime the push button is pressed the parking lights and the RED Led on the side of the EVO-ONE will blink. 7 - Then Press and Release the Brake pedal. 8 - Seconds later the RED LED on the side of the EVO-ONE will blink once to confirm that the MyCar ID has been learned to the EVO-ONE.

0

MyCar Programming without valet switch

How do I enter programming mode to get the MyCar module programmed without a valet switch? I have a 2013 Toyota Tundra and installed the Evo One in 2015. Everything works fine. I'm unable to get the Evo One into programming mode to accept the MyCar Telematics module (because I never had a valet switch). Is there any other way to get into programming mode without a valet switch?

0

MyCar Telematics starts then turns off after a few seconds

Vehicle: 2011 Toyota Corolla S (G-Key), manufactured in CAN.

Evo-One w/T-harness installed and working properly using OEM remote (3x lock to start).

 

When trying to start vehicle via the MyCar app, the engine will start and as soon as the doors auto lock the engine will shut off.

 

I have installed the MyCar Controls telematics unit based on the guide here: http://cdn02.fortin.ca/download/64631/autolink-install-guide-64631.pdf#page9

I used the HRN-LLRS-01 connector as instructed.

“Fortin 2” selected in RF section of configuration tab in FlashLink Manager.

MyCar Controls app Device Protocol: Fortin

 

Please help!

0

MyCar app not showing runtime and only starts less than half time.

2014 RAV4. EVO All. Crimestopper Cool Start RS00-G5. T-harness. I finally got this setup to work with the OEM black H-key remote with 3X Lock press. I still don’t get a parking light conformation, and the doors won’t unlock, via automatically or with the fob. The MyCar app shows battery and signal levels, and GPS location. No runtime, or remote start conformation. It only seems to start after I open the map and it is located. Then it will start, shutdown and locks require the same. I do have a Fortin flashing tool, and don’t know what else to do. Please help?!?! Thank you!

0

EVO-One set for 30 min runtime but shutdown after 15 min

EVO-One set for 30 min runtime only running for 15 min MYcar shows 30 min runtime when starting truck just runs for 15 min shutdown howerver app is still counting down

0

Using Evo-One with MyCar Module on 2018 Toyota Tundra

Trying to get MyCar module to work with an Evo-One that works as expected with OEM key fob. Connect it Evo-one and program. Appears to program correctly, proper light flash after hold then pushing valet button 5 times with key on, hit brake and get confirmation. MyCar app shows where my car is on map, voltage of car and cell signal. It will not start car of do other functions. Fortin Tech says Evo-one should work with thos out of the box. cAN NOT FIND ANYWHERE IN fortan software to program cellular module.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer